Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › 2012.12–2013.11
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047059 PARKING ASSIST MONITOR SYSTEM U

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  TERMINALS OF ECU  


REAR TELEVISION CAMERA ASSEMBLY


a.
E240561E02
1.5,0.104 1.938,0.365 0.438,0.26 1.615,0.156 1.927,0.354 0.313,0.198 10 U6

Disconnect the U6 television camera assembly.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U6-6 (CB+) - Body ground B - Body ground Power source Ignition switch ON Shift lever in R 5.5 to 7.05 V
U6-1 (CURT) - Body ground W - Body ground Ground Always Below 1 Ω


c.

Reconnect the U6 television camera assembly connector.


d.

Check for pulses between each terminal of the connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U6-3 (CV+) - U6-2 (CV-) W - R Video signal Ignition switch ON
Shift lever in R
Camera lens not covered, displaying an image
Pulse generation (See waveform 1)
Ignition switch ON
Shift lever in R
Camera lens covered, blacking out screen
Pulse generation (See waveform 2)

HINT:

A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the navigation ECU sub-assembly with the connector connected. If the result is not as specified, the television camera assembly may have a malfunction.



e.
E265840C03
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens not covered, displaying an image)
*b Waveform 2 (camera lens covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

HINT:

A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the navigation ECU sub-assembly with the connector connected.


i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Terminal No. (Symbol) U6-3 (CV+) - U6-5 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, shift lever in R

HINT:

The video waveform changes according to the image sent by the television camera assembly.



ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Terminal No. (Symbol) U6-3 (CV+) - U6-5 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, shift lever in R

HINT:

The video waveform changes according to the image sent by the television camera assembly.