Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › 2012.12–2013.11
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047059 PARKING ASSIST MONITOR SYSTEM D

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  DIAGNOSIS SYSTEM  


PARKING ASSIST MONITOR DIAGNOSIS SYSTEM


a.

For parking assist monitor system diagnosis, signals received by the navigation ECU sub-assembly can be checked and the parking assist monitor system can be calibrated, adjusted and checked using the navigation ECU sub-assembly.

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (Click here Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION).


HINT:

The displayed items may differ depending on vehicle specifications.




DIAGNOSIS SCREEN TRANSITION (during parking assist monitor system initialization)


E259920E01
0.147,0.095 0.919,0.307 0.772,0.211 12 Example:

E226187


DIAGNOSIS SCREEN TRANSITION (after parking assist monitor system initialization)


E259920E01
0.147,0.095 0.919,0.307 0.772,0.211 12 Example:


E226189

VEHICLE SIGNAL CHECK



b.
E226190

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


c.
E249275

Select "Vehicle Signal" on the "Function Check/Setting I" screen.


d.
E225776

Vehicle Signal Check Mode

i.

When the "Vehicle Signal Check Mode" screen is displayed, check the item displayed for "REV".

HINT:
·

Only conditions having inputs are displayed.

·

This screen displays vehicle signals input to the navigation ECU sub-assembly.







CAR SIGNAL CHECK (parking assist monitor system input signals)


a.
E226190

Start diagnostic mode (Click here Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>Guide Lines are Displayed with Vehicle Center Line).

i.

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E249275

Select "Camera Setting" on the "Function Check/Setting I" screen.


iii.
E226194

Select "Next" on the "Car Information Check" screen.

HINT:

After "Next" is selected, the screen transitions differ depending on whether initialization of the parking assist monitor system was performed after the navigation ECU sub-assembly was replaced.

Parking Assist Monitor System Initialization Screen Transition
Not performed Car Signal Check screen
Performed Mode Setting screen



iv.
E233966

When the screen changes to the "Mode Setting" screen, select "Back Camera Setting" to display the "Car Signal Check" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.
E233967

Car Signal Check

i.

On the "Car Signal Check" screen, it is possible to inspect the state of signals and check the settings.

Item Inspection Detail Note
BCTY Back door courtesy switch signal input When "CHK" (red) is displayed, selecting "Next" will not change to the next screen.

HINT:
·

When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.


·

If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".





c.

BCTY inspection

HINT:

If "CHK" (red) is displayed for "BCTY", check for DTCs and perform troubleshooting based on the output DTCs (Click here Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>DTC CHECK / CLEAR).





CALIBRATION WHEN SERVICING VEHICLE


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (Click here Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION).