Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › 2012.12–2013.11
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047059 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1622  Open or Short Circuit in Back Camera Signal  


DESCRIPTION

This DTC is stored if the navigation ECU sub-assembly judges that the signals or signal lines between the navigation ECU sub-assembly and the television camera assembly are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Open or Short Circuit in Back Camera Signal Open or short in the television camera assembly signal circuit
·

Television camera assembly

·

Navigation ECU sub-assembly

·

Harness or connector



WIRING DIAGRAM

E270977E08
1.75,0.552 2.052,0.75 0.302,0.198 10 false G49 1.75,1.01 2.208,1.208 0.458,0.198 10 false G49 1.75,1.479 2.208,1.677 0.458,0.198 10 false G49 1.75,1.958 2.208,2.156 0.458,0.198 10 false G49 1.729,2.469 2.344,2.667 0.615,0.198 10 false G138 1.854,0.333 2,0.521 0.146,0.188 10 false 7 1.813,0.802 2.125,1 0.313,0.198 10 false 16 1.865,1.271 2.021,1.469 0.156,0.198 10 false 8 1.823,1.75 2.135,1.948 0.313,0.198 10 false 15 1.854,2.24 2.01,2.438 0.156,0.198 10 false 7 5.479,0.438 5.635,0.635 0.156,0.198 10 false 6 5.5,1.354 5.656,1.552 0.156,0.198 10 false 3 5.5,0.896 5.656,1.094 0.156,0.198 10 false 2 5.5,1.844 5.656,2.042 0.156,0.198 10 false 5 5.708,0.552 6.167,0.75 0.458,0.198 10 false CB+ 5.708,1.479 6.167,1.677 0.458,0.198 10 false CV+ 5.729,1.01 6.188,1.208 0.458,0.198 10 false CV- 5.719,1.948 6.333,2.146 0.615,0.198 10 false CGND 5.125,2.458 5.438,2.656 0.313,0.198 10 false U6 5.125,2.656 6.958,2.885 1.833,0.229 10 false Television Camera Assembly 0.323,3.094 2.292,3.333 1.969,0.24 10 false Navigation ECU Sub-assembly 0.188,3.438 1.281,3.615 1.094,0.177 10 false *: Shielded 1.333,0.542 1.792,0.74 0.458,0.198 10 false CA+ 1.448,1.01 1.76,1.208 0.313,0.198 10 false V- 1.427,1.469 1.74,1.667 0.313,0.198 10 false V+ 1.24,1.958 1.854,2.156 0.615,0.198 10 false CGND 1.26,2.479 1.875,2.677 0.615,0.198 10 false GND1 2.625,2.104 2.781,2.292 0.156,0.188 10 false * 3.75,2.115 3.906,2.313 0.156,0.198 10 false * 4.854,2.115 5.01,2.313 0.156,0.198 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the navigation ECU sub-assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (Click here Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (Click here Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the G49 navigation ECU sub-assembly connector.


b.

Disconnect the U6 television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G49-7 (CA+) - U6-6 (CB+) Always Below 1 Ω
G49-8 (V+) - U6-3 (CV+) Always Below 1 Ω
G49-16 (V-) - U6-2 (CV-) Always Below 1 Ω
G49-15 (CGND) - U6-5 (CGND) Always Below 1 Ω
G49-7 (CA+) - Body ground Always 10 kΩ or higher
G49-8 (V+) - Body ground Always 10 kΩ or higher
G49-16 (V-) - Body ground Always 10 kΩ or higher
G49-15 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK NAVIGATION ECU SUB-ASSEMBLY (V-, CGND, CA+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK NAVIGATION ECU SUB-ASSEMBLY (V-, CGND, CA+)
a.
E216447C14
1.448,0.323 1.938,0.615 0.49,0.292 1.385,1.781 1.073,2.448 1.073,2.448 0.74,2.448 false 1.24,1.781 0.719,1.781 false 1.365,1.615 1.052,0.938 1.052,0.938 0.719,0.938 false 0.542,1.688 0.875,1.865 0.333,0.177 10 V- 0.313,2.365 0.75,2.542 0.438,0.177 10 CGND 0.167,0.104 0.604,0.281 0.438,0.177 10 *a 1.563,0.375 1.896,0.563 0.333,0.188 10 G49 0.375,0.854 0.708,1.031 0.333,0.177 10 CA+
*a Component with harness connected
(Navigation ECU Sub-assembly)


Reconnect the G49 navigation ECU sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G49-15 (CGND) - Body ground Always Below 1 Ω
G49-16 (V-) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G49-7 (CA+) - G49-15 (CGND) Ignition switch ON, shift lever in R 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

3.CHECK NAVIGATION ECU SUB-ASSEMBLY (V+, GND1)

NG

3.CHECK NAVIGATION ECU SUB-ASSEMBLY (V+, GND1)
a.

Reconnect the U6 television camera assembly connector.

E271051C09
0.458,0.531 0.865,0.76 0.406,0.229 1.833,0.552 2.292,0.771 0.458,0.219 3.438,2.333 3.583,2.333 3.583,2.333 3.781,1.813 false 4.198,2.344 4.063,2.344 4.063,2.344 3.875,1.708 false 5.448,2.208 5.594,2.208 5.594,2.208 5.792,1.688 false 6.229,2.271 6.094,2.271 6.094,2.271 5.906,1.635 false 0.479,2.063 0.365,1.292 false 1.656,2.01 1.833,2.01 1.833,2.01 2.042,1.49 false 0.135,0.365 0.448,0.563 0.313,0.198 10 false *a 3.385,0.365 3.698,0.563 0.313,0.198 10 false *b 5.375,0.375 5.688,0.573 0.313,0.198 10 false *c 3.115,1.344 3.573,1.542 0.458,0.198 10 false GND 5.115,1.344 5.573,1.542 0.458,0.198 10 false GND 3.26,2.25 3.573,2.448 0.313,0.198 10 false *d 4.24,2.25 4.552,2.448 0.313,0.198 10 false *e 5.271,2.125 5.583,2.323 0.313,0.198 10 false *d 6.281,2.188 6.594,2.385 0.313,0.198 10 false *e 0.521,0.563 0.979,0.76 0.458,0.198 10 false G49 0.396,2.104 0.708,2.302 0.313,0.198 10 false V+ 1.25,1.938 1.865,2.135 0.615,0.198 10 false GND1 1.885,0.583 2.5,0.781 0.615,0.198 10 false G138
*a Component with harness connected
(Navigation ECU Sub-assembly)
*b Waveform 1 (camera lens is not covered, displaying an image)
*c Waveform 2 (camera lens is covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -



b.

Check the waveform of the television camera assembly using an oscilloscope.

HINT:

A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the navigation ECU sub-assembly with the connector connected.


Item Content
Terminal No. (Symbol) G49-8 (V+) - G138-7 (GND1)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, shift lever in R

HINT:

The video waveform changes according to the image sent by the television camera assembly.



Result:
Proceed to
Waveform is as shown in the illustration
Waveform is not as shown in the illustration



Waveform is as shown in the illustration

Waveform is not as shown in the illustration