Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › 2012.12–2013.11
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047059 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the navigation ECU sub-assembly receives a signal via CAN communication from the spiral with sensor cable sub-assembly that indicates a power supply problem.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1625 Open or Short in Steering Angle Sensor +B Open or short in spiral with sensor cable sub-assembly power source
·

Harness or connector

·

Spiral with sensor cable sub-assembly



WIRING DIAGRAM

E224380E43
1.125,3.219 2.875,3.396 1.75,0.177 10 : CAN Communication Line 3.229,0.604 3.583,0.781 0.354,0.177 10 BAT 3.229,1.708 3.563,1.885 0.333,0.177 10 ESS 5.469,2.198 6.51,2.552 1.042,0.354 10 Navigation ECU Sub-assembly 2.021,1.344 3.031,1.521 1.01,0.177 10 ECU-IG NO. 1 2.052,0.792 3,0.969 0.948,0.177 10 ECU-B NO. 1 0.385,1.188 1.76,1.417 1.375,0.229 10 from IG1 NO. 1 Relay 0.938,0.635 1.865,0.813 0.927,0.177 10 from Battery 2.969,2.344 4.375,2.76 1.406,0.417 10 Spiral with Sensor Cable Sub-assembly 3.031,0.51 3.156,0.688 0.125,0.177 10 5 3.031,1.052 3.156,1.229 0.125,0.177 10 4 3.031,1.604 3.156,1.781 0.125,0.177 10 1 3.229,1.156 3.531,1.333 0.302,0.177 10 IG 2.979,2.177 3.323,2.354 0.344,0.177 10 G12

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the navigation ECU sub-assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (Click here Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (Click here Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY POWER SOURCE)
a.
E224381C02
1.49,0.156 1.979,0.448 0.49,0.292 2.063,1.521 2.49,1.479 false 1.865,1.563 1.865,1.865 1.865,1.865 2.49,1.865 false 1.427,1.583 1.427,1.885 1.427,1.885 0.802,1.885 false 0.469,1.813 0.885,2.01 0.417,0.198 10 ESS 2.542,1.781 2.958,1.979 0.417,0.198 10 IG 2.531,1.375 2.948,1.573 0.417,0.198 10 BAT 0.208,0.073 0.625,0.271 0.417,0.198 10 *a 1.615,0.219 1.885,0.396 0.271,0.177 10 G12
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)


Disconnect the G12 spiral with sensor cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G12-1 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G12-4 (IG) - G12-1 (ESS) Ignition switch ON 11 to 14 V
G12-5 (BAT) - G12-1 (ESS) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR