Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM3090E _58 Vehicle Interior _008429 LIGHTING (INT) _0047052 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  IG Signal Circuit  


DESCRIPTION

This circuit detects whether the ignition switch is ON or off, and sends this information to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E270708E01
3.615,0.615 3.927,0.813 0.313,0.198 10 3D 3.615,0.438 3.927,0.635 0.313,0.198 10 40 3.615,1.156 3.927,1.344 0.313,0.188 10 15 3.615,1.344 3.927,1.542 0.313,0.198 10 3C 3.604,2.229 3.917,2.427 0.313,0.198 10 3C 3.615,3.031 3.927,3.229 0.313,0.198 10 3D 3.615,1.906 3.927,2.104 0.313,0.198 10 3A 3.646,1.708 3.958,1.896 0.313,0.188 10 1 3.615,2.073 3.927,2.26 0.313,0.188 10 43 3.667,2.854 3.979,3.042 0.313,0.188 10 9 5.729,0.479 6.042,0.667 0.313,0.188 10 32 5.99,0.594 6.469,0.781 0.479,0.188 10 IG 4.219,1.49 5.219,1.667 1,0.177 10 ECU-IG NO.2 4.448,2.51 5.177,2.677 0.729,0.167 10 IG1 NO.1 3.865,3.74 5.865,4.156 2,0.417 10 Instrument Panel Junction Block Assembly 0.531,2.208 2.625,2.573 2.094,0.365 10 from Certification ECU (Smart Key ECU Assembly)*2 0.146,1.198 2.208,1.417 2.063,0.219 12 w/o Stop and Start System: 1.885,1.885 2.885,2.063 1,0.177 10 from Battery 0.615,2.844 2.052,3.021 1.438,0.177 10 from Ignition Switch*3 0.125,0.604 2.344,0.813 2.219,0.208 10 from Engine Stop and Start ECU*1 5.458,4.521 7.104,4.854 1.646,0.333 10 Main Body ECU (Multiplex Network Body ECU) 5.479,4.344 5.792,4.531 0.313,0.188 10 A 0.125,4.781 2.167,4.979 2.042,0.198 10 *1: w/ Stop and Start System 0.135,5.052 2.177,5.25 2.042,0.198 10 *2: w/ Entry and Start System 0.135,5.333 2.177,5.531 2.042,0.198 10 *3: w/o Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.READ VALUE USING GTS (IG SW)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG SW Ignition switch ON signal ON or OFF ON: Ignition switch ON
OFF: Ignition switch off
"OFF" is also displayed for this item when the ignition switch is ACC.
Body Electrical > Main Body > Data List
Tester Display
IG SW
50003 123 30
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check the vehicle type.

Result:
Proceed to
w/o Stop and Start System
w/ Stop and Start System




w/o Stop and Start System

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)

w/ Stop and Start System

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
a.
E270693C01
0.792,0.781 1.208,1.042 0.417,0.26 0.292,2.094 0.708,2.354 0.417,0.26 0.229,3.604 0.646,3.865 0.417,0.26 0.156,0.125 0.469,0.281 0.313,0.156 10 *a 0.917,0.833 1.229,0.99 0.313,0.156 10 3A 0.354,3.646 0.667,3.802 0.313,0.156 10 3D 0.417,2.135 0.729,2.292 0.313,0.156 10 3C
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3A-1 - Body ground Always 11 to 14 V
3C-43 - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-9 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY CIRCUIT)
a.

Disconnect the 3C and 3D instrument panel junction block assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-15 - 3D-40 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO.1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO.1 RELAY)
a.
E270709N01
0.854,0.469 1.281,0.75 0.427,0.281 0.115,1.667 0.542,1.948 0.427,0.281 0.083,2.99 0.51,3.271 0.427,0.281 1.49,3.615 1.917,3.896 0.427,0.281 2.792,4.354 2.99,4.104 false 0.979,0.531 1.292,0.729 0.313,0.198 10 3A 0.25,1.729 0.563,1.927 0.313,0.198 10 3C 0.229,3.063 0.542,3.26 0.313,0.198 10 3D 1.656,3.667 1.969,3.865 0.313,0.198 10 A 2.646,4.313 2.958,4.51 0.313,0.198 10 IG

Remove the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-1 - 3C-15 Battery voltage applied between terminals 3C-43 and 3D-9 Below 1 Ω
Battery voltage not applied between terminals 3C-43 and 3D-9 10 kΩ or higher
A-32 (IG) - 3D-40 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
a.
E270710C01
0.156,0.99 0.542,1.24 0.385,0.25 0.177,0.167 0.49,0.323 0.313,0.156 10 *a 0.25,1.021 0.563,1.177 0.313,0.156 10 3D
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3D-40 - Body ground Ignition switch ON 10.5 to 14 V



Result:
Proceed to
OK
NG



OK

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
E270841N01
0.104,0.854 0.49,1.094 0.385,0.24 1.458,2.302 1.844,2.542 0.385,0.24 2.854,3.063 2.979,2.833 false 0.219,0.885 0.531,1.083 0.313,0.198 10 3D 1.604,2.354 1.917,2.552 0.313,0.198 10 A 2.688,3.031 3,3.229 0.313,0.198 10 IG

Remove the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-32 (IG) - 3D-40 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG