Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM3090E _58 Vehicle Interior _008429 LIGHTING (INT) _0047052 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  ACC Signal Circuit  


DESCRIPTION

This circuit detects whether the ignition switch is ACC or off, and sends this information to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E232514E05
5.052,2.958 6.667,3.438 1.615,0.479 10 false Main Body ECU (Multiplex Network Body ECU) 3.51,1.688 4.073,1.885 0.563,0.198 10 false ACC 4.563,1.083 5,1.26 0.438,0.177 10 false ACC 2.479,1.948 2.75,2.125 0.271,0.177 10 false 3D 2.531,1.792 2.698,1.969 0.167,0.177 10 false 9 2.479,1.406 2.813,1.583 0.333,0.177 10 false 3C 2.5,1.24 2.719,1.417 0.219,0.177 10 false 45 2.49,0.927 2.781,1.104 0.292,0.177 10 false 3A 2.531,0.76 2.656,0.938 0.125,0.177 10 false 1 1.135,0.896 2.073,1.094 0.938,0.198 10 false from Battery 0.094,1.365 1.917,1.781 1.823,0.417 10 false from Certification ECU (Smart Key ECU Assembly)*1 5.594,0.948 5.958,1.146 0.365,0.198 10 false ACC 5.365,0.854 5.573,1.042 0.208,0.188 10 false 29 5.063,2.781 5.26,2.958 0.198,0.177 10 false A 2.958,2.49 4.552,2.958 1.594,0.469 10 false Instrument Panel Junction Block Assembly 0.208,3.021 2.781,3.271 2.573,0.25 10 false *1: w/ Entry and Start System 0.208,3.354 2.354,3.615 2.146,0.26 10 false *2: w/o Entry and Start System 0.083,1.896 1.552,2.115 1.469,0.219 10 false from Ignition Switch*2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.READ VALUE USING GTS (ACC SW)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Ignition switch ACC signal ON or OFF ON: Ignition switch ACC
OFF: Ignition switch off
"ON" is also displayed for this item when the ignition switch is ON.
Body Electrical > Main Body > Data List
Tester Display
ACC SW
50003 123 31
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
a.
E270693C01
0.792,0.781 1.208,1.042 0.417,0.26 0.292,2.094 0.708,2.354 0.417,0.26 0.229,3.604 0.646,3.865 0.417,0.26 0.156,0.125 0.469,0.281 0.313,0.156 10 *a 0.917,0.833 1.229,0.99 0.313,0.156 10 3A 0.354,3.646 0.667,3.802 0.313,0.156 10 3D 0.417,2.135 0.729,2.292 0.313,0.156 10 3C
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3A-1 - Body ground Always 11 to 14 V
3C-45 - Body ground Ignition switch ACC 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-9 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.
E241347C02
1.531,0.646 1.958,0.938 0.427,0.292 2.719,1.698 2.719,1.292 false 0.115,0.156 0.427,0.313 0.313,0.156 10 *a 1.698,0.708 2.01,0.865 0.313,0.156 10 A 2.583,1.729 2.979,1.885 0.396,0.156 10 ACC
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


Remove the instrument panel junction block assembly connectors.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Reconnect the 3A, 3C and 3D instrument panel junction block assembly connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A-29 (ACC) - Body ground Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG