The main body ECU (multiplex network body ECU) receives headlight dimmer switch information signals and illuminates the clearance lights*1, parking light*2, taillights and license plate lights.
*1: w/o Side Marker Light
*2: w/ Side Marker Light
Inspect the bulbs and fuses for circuits related to this system before performing the following inspection procedure.
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
Using the GTS, perform the Active Test.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Taillight Relay | Taillight relay | ON or OFF | - |
| Tester Display |
|---|
| Taillight Relay |
| Proceed to |
|---|
| Taillights come on |
| Taillights do not come on |
Taillights come on
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Taillights do not come on
Disconnect the instrument panel junction block assembly connector.
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-1 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/o Side Marker Light:
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-1 - 3B-28 | Battery voltage applied between terminals 3A-1 and A-14 (TRLY) | Below 1 Ω |
| Battery voltage not applied between terminals 3A-1 and A-14 (TRLY) | 10 kΩ or higher | |
| 3A-1 - 3E-38 | Battery voltage applied between terminals 3A-1 and A-14 (TRLY) | Below 1 Ω |
| Battery voltage not applied between terminals 3A-1 and A-14 (TRLY) | 10 kΩ or higher |
w/ Side Marker Light
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-1 - 3B-48 | Battery voltage applied between terminals 3A-1 and A-14 (TRLY) | Below 1 Ω |
| Battery voltage not applied between terminals 3A-1 and A-14 (TRLY) | 10 kΩ or higher | |
| 3A-1 - 3B-27 | Battery voltage applied between terminals 3A-1 and A-14 (TRLY) | Below 1 Ω |
| Battery voltage not applied between terminals 3A-1 and A-14 (TRLY) | 10 kΩ or higher | |
| 3A-1 - 3B-28 | Battery voltage applied between terminals 3A-1 and A-14 (TRLY) | Below 1 Ω |
| Battery voltage not applied between terminals 3A-1 and A-14 (TRLY) | 10 kΩ or higher | |
| 3A-1 - 3C-20 | Battery voltage applied between terminals 3A-1 and A-14 (TRLY) | Below 1 Ω |
| Battery voltage not applied between terminals 3A-1 and A-14 (TRLY) | 10 kΩ or higher | |
| 3A-1 - 3E-37 | Battery voltage applied between terminals 3A-1 and A-14 (TRLY) | Below 1 Ω |
| Battery voltage not applied between terminals 3A-1 and A-14 (TRLY) | 10 kΩ or higher | |
| 3A-1 - 3E-38 | Battery voltage applied between terminals 3A-1 and A-14 (TRLY) | Below 1 Ω |
| Battery voltage not applied between terminals 3A-1 and A-14 (TRLY) | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL