Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2012.12–2015.04
RM3090E _53 Suspension _008691 TIRE PRESSURE MONITORING _0048202 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2198/98  Initialization Switch (for Test Mode DTC)  


DESCRIPTION

During test mode, when the tire pressure warning reset switch is on, the tire pressure warning light comes on and when the tire pressure warning reset switch is off, the tire pressure warning light blinks at 0.125 second intervals.

DTC No. Detection Item DTC Detection Condition Trouble Area
C2198/98 Initialization Switch (for Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning reset switch

·

Wire harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C249283
5.063,3.01 6.813,3.344 1.75,0.333 10 Tire Pressure Warning ECU and Receiver 1.885,1.563 4.271,1.844 2.385,0.281 10 Tire Pressure Warning Reset Switch 1.875,1.385 2.177,1.531 0.302,0.146 10 G71 2.292,0.875 2.396,1.052 0.104,0.177 10 2 3.427,0.875 3.531,1.052 0.104,0.177 10 1 5.073,2.813 6.115,2.969 1.042,0.156 10 M11*1, M30*2 5.271,0.896 5.385,1.052 0.115,0.156 10 3 5.448,1 5.885,1.156 0.438,0.156 10 CLSW 0.24,3.042 3.208,3.292 2.969,0.25 10 *1: for FMVSS138 Type 0.25,3.406 3.219,3.677 2.969,0.271 10 *2: for ECE-R64 Type

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.INSPECT TIRE PRESSURE WARNING RESET SWITCH
a.

Remove the tire pressure warning reset switch.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RESET SWITCH>REMOVAL


b.

Inspect the tire pressure warning reset switch.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RESET SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPLACE TIRE PRESSURE WARNING RESET SWITCH

2.CHECK HARNESS AND CONNECTOR (RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the tire pressure warning reset switch G71 connector and tire pressure warning ECU and receiver M11*1 or M30*2 connector.

*1: for FMVSS138 Type

*2: for ECE-R64 Type



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for FMVSS138 Type:
Tester Connection Condition Specified Condition
M11-3 (CLSW) - G71-1 Always Below 1 Ω
M11-3 (CLSW) or G71-1 - Body ground Always 10 kΩ or higher
G71-2 - Body ground Always Below 1 Ω

for ECE-R64 Type:
Tester Connection Condition Specified Condition
M30-3 (CLSW) - G71-1 Always Below 1 Ω
M30-3 (CLSW) or G71-1 - Body ground Always 10 kΩ or higher
G71-2 - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR