Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2012.12–2015.04
RM3090E _53 Suspension _008691 TIRE PRESSURE MONITORING _0048202 TIRE PRESSURE WARNING SYSTEM U

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  TERMINALS OF ECU  


CHECK TIRE PRESSURE WARNING ECU AND RECEIVER


C279757
2.083,0.521 2.417,0.75 0.333,0.229 2.083,0.938 2.417,1.167 0.333,0.229 0.094,0.052 0.406,0.25 0.313,0.198 10 *a 2.125,0.563 2.583,0.76 0.458,0.198 10 M11 2.125,0.979 2.583,1.177 0.458,0.198 10 M30 2.438,0.469 2.75,0.667 0.313,0.198 10 *A 2.438,0.885 2.75,1.083 0.313,0.198 10 *B
*A for FMVSS138 Type *B for ECE-R64 Type
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)
- -


a.

Disconnect the tire pressure warning ECU and receiver M11*1 or M30*2 connector and measure the voltage or resistance on the wire harness side.

*1: for FMVSS138 Type

*2: for ECE-R64 Type


for FMVSS138 Type
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M11-1 (IG) - M11-12 (E) L - W-B IG power source Ignition switch ON 10 to 16 V
M11-7 (+B) - M11-12 (E) R - W-B Power supply (from battery) Always 10 to 16 V
M11-12 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

for ECE-R64 Type
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M30-1 (IG) - M30-12 (GND) L - W-B IG power source Ignition switch ON 10 to 16 V
M30-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


b.

Connect the tire pressure warning ECU and receiver M11*1 or M30*2 connector.

*1: for FMVSS138 Type

*2: for ECE-R64 Type



c.

Measure the voltage and resistance according to the value(s) in the table below. If the result is not as specified, the ECU may have a malfunction.

HINT:

Inspect the connectors from the back side while the connectors are connected.


E129452
1.333,0.844 1.729,1.115 0.396,0.271 1.333,0.479 1.729,0.75 0.396,0.271 1.948,0.542 2.26,0.698 0.313,0.156 10 *A 1.938,0.917 2.25,1.073 0.313,0.156 10 *B 0.188,0.115 0.5,0.271 0.313,0.156 10 *a 1.396,0.531 1.854,0.729 0.458,0.198 10 M11 1.396,0.906 1.854,1.104 0.458,0.198 10 M30
*A for FMVSS138 Type *B for ECE-R64 Type
*a Component with harness connected
(Tire Pressure Warning ECU and Receiver)
- -


for FMVSS138 Type
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M11-3 (CLSW) - M11-12 (E) V - W-B Tire pressure warning reset switch
·

Ignition switch ON

·

Tire pressure warning reset switch ON


Below 1.5 V
·

Ignition switch ON

·

Tire pressure warning reset switch OFF


8 to 15 V
M11-4 (RDA) - M11-12 (E) G - W-B Output signals Ignition switch ON Pulse generation (see waveform 1)
M11-5 (PRG) - M11-12 (E) W - W-B Input signals Ignition switch ON Pulse generation (see waveform 1)

for ECE-R64 Type
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M30-3 (CLSW) - M30-12 (GND) V - W-B Tire pressure warning reset switch
·

Ignition switch ON

·

Tire pressure warning reset switch ON


Below 1.5 V
·

Ignition switch ON

·

Tire pressure warning reset switch OFF


8 to 15 V
M30-4 (RDA2) - M30-12 (GND) G - W-B Output signals Ignition switch ON Pulse generation (see waveform 1)
M30-5 (PRG2) - M30-12 (GND) W - W-B Input signals Ignition switch ON Pulse generation (see waveform 1)


d.
C240058C02
2.875,1.219 3.115,1.427 0.24,0.208 10 *b 0.104,0.083 0.313,0.302 0.208,0.219 10 *a
*a Example
*b GND


Using an oscilloscope, check waveform 1.

Waveform 1:
Item Contents
Terminal M11-4 (RDA) - M11-12 (E)*1
M11-5 (PRG) - M11-12 (E)*1
M30-4 (RDA2) - M30-12 (GND)*2
M30-5 (PRG2) - M30-12 (GND)*2
Tool setting 5 V/DIV, 5 ms./DIV.
Vehicle condition Ignition switch ON

*1: for FMVSS138 Type

*2: for ECE-R64 Type


HINT:

The waveform shown in the illustration is an example. If the tester displays a waveform that alternates between high and low, where high is a voltage that is between the IG power source voltage and a voltage 2.2 V lower than the IG power source voltage, and where low is a voltage of between 0 and 1.2 V, the ECU can be judged normal.