Home › Engine / Hybrid System › 3ZR-FAE EMISSION CONTROL › CANISTER
RM3090E _51 Engine / Hybrid System _008389 3ZR-FAE EMISSION CONTROL _0046826 CANISTER G

3ZR-FAE EMISSION CONTROL  CANISTER  INSPECTION  


PROCEDURE

Hide 1.INSPECT CHARCOAL CANISTER ASSEMBLY

a.
A182969
1.75,0.656 1.875,0.146 1.875,0.146 2.063,0.146 true 2.448,0.906 2.781,0.302 2.781,0.302 2.99,0.302 true 1.51,1.865 1.75,1.865 1.75,1.865 2.052,1.323 true 2.094,0.063 2.271,0.229 0.177,0.167 10 *1 3.021,0.229 3.188,0.375 0.167,0.146 10 *2 1.344,1.792 1.5,1.948 0.156,0.156 10 *3
*1 Port A
*2 Port B
*3 Port C
V100135

Air


Close port C, apply compressed air to port A and check that air flows out from port B.

If the result is not as specified, replace the fuel suction plate sub-assembly.


b.
A182970
1.625,0.635 1.75,0.177 1.75,0.177 1.938,0.177 true 2.302,0.885 2.531,0.25 2.531,0.25 2.729,0.25 true 1.385,1.854 1.552,1.854 1.552,1.854 1.906,1.281 true 1.969,0.094 2.146,0.271 0.177,0.177 10 *1 2.75,0.167 2.917,0.323 0.167,0.156 10 *2 1.208,1.781 1.385,1.969 0.177,0.188 10 *3
*1 Port A
*2 Port B
*3 Port C
V100135

Air


Close port C, apply compressed air to port B and check that air flows out from port A.

If the result is not as specified, replace the fuel suction plate sub-assembly.


c.
A182971
1.594,0.635 1.771,0.208 1.771,0.208 1.969,0.208 true 2.323,0.875 2.5,0.188 2.5,0.188 2.708,0.188 true 1.375,1.854 1.583,1.854 1.583,1.854 1.917,1.292 true 1.99,0.125 2.156,0.281 0.167,0.156 10 *1 2.729,0.115 2.885,0.271 0.156,0.156 10 *2 1.198,1.792 1.354,1.948 0.156,0.156 10 *3
*1 Port A
*2 Port B
*3 Port C
V100135

Air


Apply compressed air to port B and check that air flows out from port A and port C.

If the result is not as specified, replace the fuel suction plate sub-assembly.


d.
A182972
1.781,0.51 1.854,0.125 1.854,0.125 2.021,0.125 true 2.292,0.719 2.531,0.208 2.531,0.208 2.896,0.208 true 1.281,1.646 1.552,1.646 1.552,1.646 2.052,1.177 true 2.052,0.052 2.219,0.219 0.167,0.167 10 *1 2.927,0.125 3.115,0.302 0.188,0.177 10 *2 1.104,1.573 1.271,1.74 0.167,0.167 10 *3
*1 Port A
*2 Port B
*3 Port C


Close ports A and C, and apply compressed air to port B to check for leaks.

If the result is not as specified, replace the fuel suction plate sub-assembly.