Home › Engine / Hybrid System › 2AD-FHV INTAKE / EXHAUST › EXHAUST MANIFOLD W/ TURBOCHARGER
RM3090E _51 Engine / Hybrid System _008382 2AD-FHV INTAKE / EXHAUST _0048455 EXHAUST MANIFOLD W/ TURBOCHARGER A

2AD-FHV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL STUD BOLT

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.

For turbocharger sub-assembly:

i.
A206341
0.75,3.531 1.063,3.688 0.313,0.156 10 *a 1.948,3.375 2.26,3.531 0.313,0.156 10 *b 1.958,3.938 2.271,4.094 0.313,0.156 10 *c
*a 32 mm (1.26 in.)
*b 20 mm (0.787 in.)
*c 10 mm (0.394 in.)


Using an E8 "TORX" wrench, install the 3 stud bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.
A291341
0.917,2.677 1.229,2.833 0.313,0.156 10 *a 1.708,2.354 2.021,2.51 0.313,0.156 10 *b 0.938,4.031 1.25,4.188 0.313,0.156 10 *c 1.719,3.865 2.031,4.021 0.313,0.156 10 *d 1.198,0.135 1.354,0.333 0.156,0.198 10 A 0.375,0.573 0.531,0.771 0.156,0.198 10 A 1.438,0.469 1.594,0.667 0.156,0.198 10 B 1.031,1.552 1.188,1.75 0.156,0.198 10 B 1.719,3.094 2.031,3.25 0.313,0.156 10 *b 1.729,4.188 2.042,4.344 0.313,0.156 10 *e 1.333,3.5 1.49,3.698 0.156,0.198 10 B 1.333,2.052 1.49,2.25 0.156,0.198 10 A
*a 43 mm (1.69 in.)
*b 16 mm (0.630 in.)
*c 24.5 mm (0.965 in.)
*d 12 mm (0.472 in.)
*e 9.0 mm (0.354 in.)


Install the 2 stud bolts labeled A shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


iii.

Using an E5 "TORX" wrench, install the 2 stud bolts labeled B shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


iv.
A206342
0.698,3.292 1.01,3.448 0.313,0.156 10 *a 1.938,2.74 2.25,2.896 0.313,0.156 10 *b 1.927,3.896 2.24,4.052 0.313,0.156 10 *c
*a 47 mm (1.85 in.)
*b 14 mm (0.551 in.)
*c 15 mm (0.591 in.)


Using an E8 "TORX" wrench, install the stud bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)



b.
A291348
0.552,2.531 0.865,2.688 0.313,0.156 10 *a 1.958,2.198 2.271,2.354 0.313,0.156 10 *b 1.958,2.938 2.271,3.094 0.313,0.156 10 *b
*a 43 mm (1.69 in.)
*b 16 mm (0.630 in.)


For exhaust manifold:

Install the stud bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 17141 2.INSTALL EXHAUST MANIFOLD AND TURBOCHARGER SUB-ASSEMBLY

a.
A273051
1.25,2.333 1.417,2.333 1.417,2.333 1.417,2.667 false 1.75,2.333 1.583,2.333 1.583,2.333 1.583,2.833 true 1.792,2.24 2.104,2.396 0.313,0.156 10 *1 1.094,2.229 1.406,2.385 0.313,0.156 10 *2 1.625,0.365 1.781,0.563 0.156,0.198 10 A 2.229,0.375 2.385,0.573 0.156,0.198 10 A
*1 Collar
*2 Groove


Temporarily install a new gasket, and the exhaust manifold and 2 collars with 2 new nuts labeled A. Tighten the nuts until the mating surface of the exhaust manifold contacts the cylinder head.


b.

Temporarily install the 6 collars with 6 new nuts.

HINT:
·

When installing the collars, pay attention to the mounting orientation. The ring groove of the collar should be on the outside. Refer to the illustration.

·

Do not fully tighten the nuts as doing so may result in misalignment of the exhaust manifold.




c.

Install a new gasket and the turbocharger sub-assembly with 3 new nuts.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)


d.

Connect the vacuum hose.


e.

Install the 2 collars and a new turbocharger stay with 2 new nuts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:

Do not reuse the turbocharger stay.



f.

Tighten the 8 nuts of the exhaust manifold.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 15482 3.INSTALL NO. 2 TURBO OIL PIPE

a.

Install the No. 2 turbo oil pipe and 2 new gaskets with the 2 union bolts.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 16289 4.INSTALL NO. 5 WATER BY-PASS PIPE

a.

Install the No. 5 water by-pass pipe with the 2 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 16267 5.CONNECT NO. 3 WATER BY-PASS HOSE

a.

Connect the No. 3 water by-pass hose to the No. 1 water by-pass pipe, and slide the clamp to secure the hose.


Hide 17271 6.INSTALL NO. 1 TURBO INSULATOR

a.

Install the No. 1 turbo insulator with the 2 bolts.

Torque:
21 N*m (209 kgf*cm, 15 ft.*lbf)


Hide 15474 7.INSTALL TURBO OIL OUTLET PIPE

a.

Install 2 new gaskets to the turbo oil outlet pipe.


b.

Install the turbo oil outlet pipe with the 2 bolts and 2 nuts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 25601L 8.INSTALL EGR COOLER WITH PIPE ASSEMBLY

Hide 9.PERFORM TURBOCHARGER INITIALIZATION