Home › Drivetrain › EA64 MANUAL TRANSMISSION / TRANSAXLE › OUTPUT SHAFT
RM3090E _52 Drivetrain _008755 EA64 MANUAL TRANSMISSION / TRANSAXLE _0048557 OUTPUT SHAFT G

EA64 MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  INSPECTION  


PROCEDURE

Hide 33321 1.INSPECT NO. 1 OUTPUT SHAFT

a.
C112463

Check the No. 1 output shaft for wear and damage.


b.

Using a dial indicator, measure the No. 1 output shaft runout.

Maximum runout:

0.03 mm (0.00118 in.)


If the runout is more than the maximum, replace the No. 1 output shaft.


c.
C112464
0.517,0.988 0.517,0.656 false 2.903,0.959 2.903,0.614 false 0.851,0.962 0.851,0.641 false 1.369,0.926 1.369,0.62 false 1.623,0.919 1.623,0.622 false 2.19,0.884 2.19,0.603 false 1.304,0.448 1.446,0.595 0.142,0.147 10 C 2.863,0.439 3.005,0.586 0.142,0.147 10 F 0.464,0.468 0.607,0.615 0.142,0.147 10 A 2.141,0.43 2.283,0.577 0.142,0.147 10 E 1.568,0.443 1.71,0.59 0.142,0.147 10 D 0.804,0.46 0.947,0.607 0.142,0.147 10 B

Using a micrometer, measure the journal diameter of the No. 1 output shaft journal surface.

Standard Journal Diameter:
Item Specified Condition
Journal A 32.002 to 32.018 mm (1.2600 to 1.2605 in.)
Journal B 35.984 to 36.000 mm (1.4167 to 1.4173 in.)
Journal C 41.984 to 42.000 mm (1.6530 to 1.6535 in.)
Journal D 41.989 to 42.000 mm (1.6532 to 1.6535 in.)
Journal E 46.984 to 47.000 mm (1.8498 to 1.8503 in.)
Journal F 36.002 to 36.018 mm (1.4174 to 1.4180 in.)


If the outer diameter is not as specified, replace the No. 1 output shaft.


Hide 33335 2.INSPECT 1ST DRIVEN GEAR THRUST CLEARANCE

a.
C115414

Using a dial indicator, measure the 1st driven gear thrust clearance.

Standard clearance:

0.10 to 0.35 mm (0.00394 to 0.01377 in.)


Maximum clearance:

0.35 mm (0.01377 in.)


If the clearance is more than the maximum, replace the 1st driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33335 3.INSPECT 1ST DRIVEN GEAR RADIAL CLEARANCE

a.
C115416

Using a dial indicator, measure the 1st driven gear radial clearance.

Standard clearance:

0.015 to 0.068 mm (0.000591 to 0.00267 in.)


Maximum clearance:

0.068 mm (0.00267 in.)


If the clearance is more than the maximum, replace the 1st driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33332 4.INSPECT 2ND DRIVEN GEAR THRUST CLEARANCE

a.
C115415

Using a dial indicator, measure the 2nd driven gear thrust clearance.

Standard clearance:

0.11 to 0.46 mm (0.00434 to 0.0181 in.)


Maximum clearance:

0.46 mm (0.0181 in.)


If the clearance is more than the maximum, replace the 2nd driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33332 5.INSPECT 2ND DRIVEN GEAR RADIAL CLEARANCE

a.
C113596

Using a dial indicator, measure the 2nd driven gear radial clearance.

Standard clearance:

0.015 to 0.048 mm (0.000591 to 0.00188 in.)


Maximum clearance:

0.048 mm (0.00188 in.)


If the clearance is more than the maximum, replace the 2nd driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33423A 6.INSPECT 3RD DRIVEN GEAR THRUST CLEARANCE

a.
C113639

Using a feeler gauge, measure the 3rd driven gear thrust clearance.

Standard clearance:

0.11 to 0.54 mm (0.00434 to 0.0212 in.)


Maximum clearance:

0.54 mm (0.0212 in.)


If the clearance is more than the maximum, replace the 3rd driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33423A 7.INSPECT 3RD DRIVEN GEAR RADIAL CLEARANCE

a.
C113643

Using a dial indicator, measure the 3rd driven gear radial clearance.

Standard clearance:

0.015 to 0.066 mm (0.000591 to 0.00259 in.)


Maximum clearance:

0.066 mm (0.00259 in.)


If the clearance is more than the maximum, replace the 3rd driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33422B 8.INSPECT 4TH DRIVEN GEAR THRUST CLEARANCE

a.
C113640

Using a feeler gauge, measure the 4th driven gear thrust clearance.

Standard clearance:

0.10 to 0.65 mm (0.00394 to 0.0255 in.)


Maximum clearance:

0.65 mm (0.0255 in.)


If the clearance is more than the maximum, replace the 4th driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33422B 9.INSPECT 4TH DRIVEN GEAR RADIAL CLEARANCE

a.
C113644

Using a dial indicator, measure the 4th driven gear radial clearance.

Standard clearance:

0.015 to 0.066 mm (0.000591 to 0.00259 in.)


Maximum clearance:

0.066 mm (0.00259 in.)


If the clearance is more than the maximum, replace the 4th driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33428C 10.INSPECT 5TH DRIVEN GEAR THRUST CLEARANCE

a.
C113604

Using a feeler gauge, measure the 5th driven gear thrust clearance.

Standard clearance:

0.10 to 0.55 mm (0.00394 to 0.0216 in.)


Maximum clearance:

0.55 mm (0.0216 in.)


If the clearance is more than the maximum, replace the 5th driven gear, needle roller bearing or No. 2 output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33428C 11.INSPECT 5TH DRIVEN GEAR RADIAL CLEARANCE

a.
C113605

Using a dial indicator, measure the 5th driven gear radial clearance.

Standard clearance:

0.015 to 0.066 mm (0.000591 to 0.00259 in.)


Maximum clearance:

0.066 mm (0.00259 in.)


If the clearance is more than the maximum, replace the 5th driven gear, needle roller bearing or No. 2 output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33429B 12.INSPECT 6TH DRIVEN GEAR THRUST CLEARANCE

a.
C113602

Using a feeler gauge, measure the 6th driven gear thrust clearance.

Standard clearance:

0.10 to 0.55 mm (0.00394 to 0.0216 in.)


Maximum clearance:

0.55 mm (0.0216 in.)


If the clearance is more than the maximum, replace the 6th driven gear, needle roller bearing or No. 2 output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33429B 13.INSPECT 6TH DRIVEN GEAR RADIAL CLEARANCE

a.
C113603

Using a dial indicator, measure the 6th driven gear radial clearance.

Standard clearance:

0.015 to 0.066 mm (0.000591 to 0.00259 in.)


Maximum clearance:

0.066 mm (0.00259 in.)


If the clearance is more than the maximum, replace the 6th driven gear, needle roller bearing or No. 2 output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33331 14.INSPECT REVERSE DRIVEN GEAR THRUST CLEARANCE

a.
C113606

Using a feeler gauge, measure the reverse driven gear thrust clearance.

Standard clearance:

0.11 to 0.34 mm (0.00434 to 0.0133 in.)


Maximum clearance:

0.34 mm (0.0133 in.)


If the clearance is more than the maximum, replace the reverse driven gear, needle roller bearing or No. 2 output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33331 15.INSPECT REVERSE DRIVEN GEAR RADIAL CLEARANCE

a.
C113607

Using a dial indicator, measure the reverse driven gear radial clearance.

Standard clearance:

0.015 to 0.068 mm (0.000591 to 0.00267 in.)


Maximum clearance:

0.068 mm (0.00267 in.)


If the clearance is more than the maximum, replace the reverse driven gear, needle roller bearing or No. 2 output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33242F 16.INSPECT 1ST AND 2ND SHIFT FORK SHAFT

a.
C113557

Using a micrometer, measure the 1st and 2nd shift fork shaft.

Standard outer diameter:

13.982 to 14.000 mm (0.5505 to 0.5511 in.)


Minimum outer diameter:

13.982 mm (0.5505 in.)


If the outer diameter is less than the minimum, replace the 1st and 2nd shift fork shaft.


Hide 33243F 17.INSPECT 3RD AND 4TH SHIFT FORK SHAFT

a.
C278119

Using a micrometer, measure the 3rd and 4th shift fork shaft.

Standard outer diameter:

13.982 to 14.000 mm (0.5505 to 0.5511 in.)


Minimum outer diameter:

13.982 mm (0.5505 in.)


If the outer diameter is less than the minimum, replace the 3rd and 4th shift fork shaft.


Hide 33244J 18.INSPECT 5TH AND 6TH SHIFT FORK SHAFT

a.
C113559

Using a micrometer, measure the 5th and 6th shift fork shaft.

Standard outer diameter:

13.982 to 14.000 mm (0.5505 to 0.5511 in.)


Minimum outer diameter:

13.982 mm (0.5505 in.)


If the outer diameter is less than the minimum, replace the 5th and 6th shift fork shaft.


Hide 33245H 19.INSPECT REVERSE SHIFT FORK SHAFT

a.
C278121

Using a micrometer, measure the reverse shift fork shaft.

Standard outer diameter:

13.982 to 14.000 mm (0.5505 to 0.5511 in.)


Minimum outer diameter:

13.982 mm (0.5505 in.)


If the outer diameter is less than the minimum, replace the reverse shift fork shaft.


Hide 33246C 20.INSPECT NO. 5 GEAR SHIFT FORK SHAFT

a.
C278122

Using a micrometer, measure the No. 5 gear shift fork shaft.

Standard outer diameter:

15.966 to 15.984 mm (0.6286 to 0.6292 in.)


Minimum outer diameter:

15.966 mm (0.6286 in.)


If the outer diameter is less than the minimum, replace the No. 5 gear shift fork shaft.


Hide 33212A 21.INSPECT NO. 1 GEAR SHIFT FORK

a.
C113562
0.857,1.696 1.023,1.862 0.167,0.165 10 A 3.227,0.223 3.372,0.389 0.146,0.165 10 B

Using a vernier caliper, measure the No. 1 gear shift fork.

Standard inside diameter and thickness:
A:

9.50 to 9.80 mm (0.375 to 0.385 in.)

B:

14.010 to 14.043 mm (0.5516 to 0.5528 in.)


If the diameter and thickness is not as specified, replace the No. 1 gear shift fork.


Hide 33213G 22.INSPECT NO. 2 GEAR SHIFT FORK

a.
C277858
1.25,1.875 1.406,2.073 0.156,0.198 10 A 2.781,0.417 2.938,0.615 0.156,0.198 10 B 1.354,1.104 1.51,1.302 0.156,0.198 10 C

Using a vernier caliper, measure the No. 2 gear shift fork.

Standard inside diameter and thickness:
A:

9.50 to 9.80 mm (0.375 to 0.385 in.)

B:

14.010 to 14.043 mm (0.5516 to 0.5528 in.)

C:

14.70 to 15.30 mm (0.579 to 0.602 in.)


If the diameter and thickness is not as specified, replace the No. 2 gear shift fork.


Hide 33214G 23.INSPECT NO. 3 GEAR SHIFT FORK

a.
C113563
1.05,1.81 1.198,1.966 0.147,0.156 10 A 3.114,0.589 3.261,0.745 0.147,0.156 10 B

Using a vernier caliper, measure the No. 3 gear shift fork.

Standard inside diameter and thickness:
A:

9.50 to 9.80 mm (0.375 to 0.385 in.)

B:

14.010 to 14.043 mm (0.5516 to 0.5528 in.)


If the diameter and thickness is not as specified, replace the No. 3 gear shift fork.


Hide 33211 24.INSPECT REVERSE SHIFT FORK

a.
C277782
1.125,1.865 1.281,2.063 0.156,0.198 10 A 3.094,1.667 3.25,1.865 0.156,0.198 10 B 2.385,1.677 2.542,1.875 0.156,0.198 10 C

Using a vernier caliper, measure the reverse shaft fork.

Standard inside diameter and thickness:
A:

4.40 to 4.56 mm (0.174 to 0.179 in.)

B:

14.010 to 14.043 mm (0.5516 to 0.5528 in.)

C:

14.70 to 15.30 mm (0.579 to 0.602 in.)


If the diameter and thickness is not as specified, replace the reverse shaft fork.


Hide 33233A 25.INSPECT NO. 2 GEAR SHIFT HEAD

a.
C113561

Using a vernier caliper, measure the No. 2 gear shift head.

Standard inside diameter:

13.994 to 14.054 mm (0.551 to 0.553 in.)


Maximum inside diameter:

14.054 mm (0.553 in.)


If the inside diameter is more than the maximum, replace the No. 2 gear shift head.


Hide 33234A 26.INSPECT NO. 3 GEAR SHIFT HEAD

a.
C113560
0.697,0.115 0.867,0.282 0.17,0.168 10 A 3.057,1.155 3.227,1.323 0.17,0.168 10 B

Using a vernier caliper, measure the No. 3 gear shift head.

Standard inside diameter:
A:

15.994 to 16.054 mm (0.630 to 0.632 in.)

B:

14.20 to 14.25 mm (0.560 to 0.561 in.)


Maximum inside diameter:
A:

16.054 mm (0.632 in.)

B:

14.25 mm (0.561 in.)


If the inside diameter is more than the maximum, replace the No. 3 gear shift head.


Hide 33335 27.INSPECT 1ST DRIVEN GEAR

a.
C113611

Using a cylinder gauge, measure the inside diameter of the 1st driven gear.

Standard inside diameter:

53.015 to 53.040 mm (2.0872 to 2.0881 in.)


Maximum inside diameter:

53.040 mm (2.0881 in.)


If the inside diameter is more than the maximum, replace the 1st driven gear.


Hide 33332 28.INSPECT 2ND DRIVEN GEAR

a.
C113612

Using a cylinder gauge, measure the inside diameter of the 2nd driven gear.

Standard inside diameter:

56.015 to 56.030 mm (2.2054 to 2.2059 in.)


Maximum inside diameter:

56.030 mm (2.2059 in.)


If the inside diameter is more than the maximum, replace the 2nd driven gear.


Hide 33423A 29.INSPECT 3RD DRIVEN GEAR

a.
C113613

Using a cylinder gauge, measure the inside diameter of the 3rd driven gear.

Standard inside diameter:

42.015 to 42.040 mm (1.6542 to 1.6551 in.)


Maximum inside diameter:

42.040 mm (1.6551 in.)


If the inside diameter is more than the maximum, replace the 3rd driven gear.


Hide 33422B 30.INSPECT 4TH DRIVEN GEAR

a.
C113614

Using a cylinder gauge, measure the inside diameter of the 4th driven gear.

Standard inside diameter:

48.015 to 48.040 mm (1.8904 to 1.8913 in.)


Maximum inside diameter:

48.040 mm (1.8913 in.)


If the inside diameter is more than the maximum, replace the 4th driven gear.


Hide 33037B 31.INSPECT 1ST DRIVEN GEAR SYNCHRONIZER RING SET

C113625

a.

Check for wear and damage.


b.

Coat the 1st driven gear cone with gear oil.


c.

Turn the synchronizer ring in both directions while pushing it against the 1st driven gear cone and check that it locks in both directions.

If the synchronizer ring does not lock, replace the synchronizer ring.


d.
C113618

Using a feeler gauge, measure the clearance between the synchronizer ring back and gear spline end.

Standard clearance:

0.98 to 1.82 mm (0.0386 to 0.0716 in.)


Minimum clearance:

0.98 mm (0.0386 in.)


If the clearance is less than the minimum, replace the 1st driven gear synchronizer ring set.


Hide 33037B 32.INSPECT 2ND DRIVEN GEAR SYNCHRONIZER RING SET

C113626

a.

Check for wear and damage.


b.

Coat the 2nd driven gear cone with gear oil.


c.

Turn the synchronizer ring in both directions while pushing it against the 2nd driven gear cone and check that it locks in both directions.

If the synchronizer ring does not lock, replace the synchronizer ring.


d.
C113619

Using a feeler gauge, measure the clearance between the synchronizer ring back and 2nd gear spline end.

Standard clearance:

1.08 to 1.92 mm (0.0426 to 0.0755 in.)


Minimum clearance:

1.08 mm (0.0426 in.)


If the clearance is less than the minimum, replace the 2nd driven gear synchronizer ring set.


Hide 33047 33.INSPECT 3RD DRIVEN GEAR SYNCHRONIZER RING SET

C113627

a.

Check for wear and damage.


b.

Coat the 3rd driven gear cone with gear oil.


c.

Turn the synchronizer ring in both directions while pushing it against the 3rd driven gear cone and check that it locks in both directions.

If the synchronizer ring does not lock, replace the synchronizer ring.


d.
C113620

Using a feeler gauge, measure the clearance between the 3rd gear synchronizer ring back and spline end.

Standard clearance:

1.00 to 2.00 mm (0.0394 to 0.0787 in.)


Minimum clearance:

1.00 mm (0.0394 in.)


If the clearance is less than the minimum, replace the 3rd driven gear synchronizer ring set.


Hide 33037B 34.INSPECT 4 TH DRIVEN GEAR SYNCHRONIZER RING SET

C113628

a.

Check for wear and damage.


b.

Coat the 4th driven gear cone with gear oil.


c.

Turn the synchronizer ring in both directions while pushing it against the 4th driven gear cone and check that it locks in both directions.

If the synchronizer ring does not lock, replace the synchronizer ring.


d.
C113621

Using a feeler gauge, measure the clearance between the 4th gear synchronizer ring back and spline end.

Standard clearance:

0.92 to 1.88 mm (0.0363 to 0.0740 in.)


Minimum clearance:

0.92 mm (0.0363 in.)


If the clearance is less than the minimum, replace the 4th driven gear synchronizer ring set.


Hide 33363 35.INSPECT NO. 1 TRANSMISSION HUB SLEEVE

a.
C116323
2.856,1.777 2.999,1.94 0.144,0.163 10 A 1.425,1.792 1.569,1.955 0.144,0.163 10 B

Using a vernier caliper, measure the clearance between the No. 1 transmission hub sleeve and the No. 1 gear shift fork.

Standard clearance (A - B):

0.10 to 0.50 mm (0.00394 to 0.0196 in.)


If the clearance is not as specified, replace the No. 1 transmission hub sleeve and No. 1 gear shift fork.


Hide 33364 36.INSPECT NO. 2 TRANSMISSION HUB SLEEVE

a.
C116324
2.796,1.78 2.952,1.943 0.156,0.163 10 A 1.224,1.782 1.369,1.939 0.145,0.156 10 B

Using a vernier caliper, measure the clearance between the No. 2 transmission hub sleeve and the No. 2 gear shift fork.

Standard clearance (A - B):

0.10 to 0.50 mm (0.00394 to 0.0196 in.)


If the clearance is not as specified, replace the No. 2 transmission hub sleeve and No. 2 gear shift fork.


Hide 33322 37.INSPECT NO. 2 OUTPUT SHAFT

a.
C112460

Check the No. 2 output shaft for wear and damage.


b.

Using a dial indicator, check the No. 2 output shaft runout.

Maximum runout:

0.03 mm (0.00118 in.)


If the runout is more than the maximum, replace the No. 2 output shaft.


c.
C112461
0.539,0.941 0.539,0.609 false 0.865,0.917 0.865,0.6 false 1.475,0.877 1.475,0.617 false 1.948,0.859 1.948,0.617 false 2.811,0.912 2.811,0.626 false 0.826,0.385 0.981,0.562 0.155,0.177 10 B 0.49,0.384 0.646,0.561 0.155,0.177 10 A 1.426,0.397 1.581,0.574 0.155,0.177 10 C 1.902,0.397 2.057,0.574 0.155,0.177 10 D 2.761,0.415 2.917,0.592 0.155,0.177 10 E

Using a micrometer, measure the journal diameter of the No. 2 output shaft journal surface.

Standard Journal Diameter:
Item Specified Condition
Journal A 32.002 to 32.018 mm (1.2600 to 1.2605 in.)
Journal B 35.984 to 36.000 mm (1.4167 to 1.4173 in.)
Journal C 41.984 to 42.000 mm (1.6530 to 1.6535 in.)
Journal D 46.984 to 47.000 mm (1.8498 to 1.8503 in.)
Journal E 35.002 to 35.018 mm (1.3781 to 1.3786 in.)


If the outer diameter is not as specified, replace the No. 2 output shaft.


Hide 33428C 38.INSPECT 5TH DRIVEN GEAR

a.
C113615

Using a cylinder gauge, measure the inside diameter of the 5th driven gear.

Standard inside diameter:

48.015 to 48.040 mm (1.890 to 1.891 in.)


Maximum inside diameter:

48.040 mm (1.891 in.)


If the inside diameter is more than the maximum, replace the 5th driven gear.


Hide 33429B 39.INSPECT 6TH DRIVEN GEAR

a.
C113616

Using a cylinder gauge, measure the inside diameter of the 6th driven gear.

Standard inside diameter:

42.015 to 42.040 mm (1.6542 to 1.6551 in.)


Maximum inside diameter:

42.040 mm (1.6551 in.)


If the inside diameter is more than the maximum, replace the 6th driven gear.


Hide 33331 40.INSPECT REVERSE DRIVEN GEAR

a.
C113617

Using a cylinder gauge, measure the inside diameter of the reverse driven gear.

Standard inside diameter:

53.015 to 53.040 mm (2.0873 to 2.0881 in.)


Maximum inside diameter:

53.040 mm (2.0881 in.)


If the inside diameter is more than the maximum, replace the reverse driven gear.


Hide 33428C 41.INSPECT 5TH DRIVEN SYNCHRONIZER RING SET

C113629

a.

Check for wear and damage.


b.

Coat the 5th driven gear cone with gear oil.


c.

Turn the synchronizer ring in both directions while pushing it against the 5th driven gear cone and check that it locks in both directions.

If the synchronizer ring does not lock, replace the synchronizer ring.


d.
C113622

Using a feeler gauge, measure the clearance between the synchronizer ring back and 5th driven gear spline end.

Standard clearance:

0.80 to 1.60 mm (0.0315 to 0.0629 in.)


Minimum clearance:

0.80 mm (0.0315 in.)


If the clearance is less than the minimum, replace the 5th driven gear synchronizer ring set.


Hide 33369B 42.INSPECT 6TH DRIVEN SYNCHRONIZER RING SET

C113630

a.

Check for wear and damage.


b.

Coat the 6th driven gear cone with gear oil.


c.

Turn the synchronizer ring in both directions while pushing it against the 6th driven gear cone and check that it locks in both directions.

If the synchronizer ring does not lock, replace the synchronizer ring.


d.
C113623

Using a feeler gauge, measure the clearance between the gear synchronizer ring back and 6th driven gear spline end.

Standard clearance:

0.80 to 1.60 mm (0.0315 to 0.0629 in.)


Minimum clearance:

0.80 mm (0.0315 in.)


If the clearance is less than the minimum, replace the 6th driven gear synchronizer ring set.


Hide 33369B 43.INSPECT REVERSE DRIVEN GEAR SYNCHRONIZER RING SET

C113631

a.

Check for wear and damage.


b.

Coat the reverse driven gear cone with gear oil.


c.

Turn the synchronizer ring in both directions while pushing it against the reverse driven gear cone and check that it locks in both directions.

If the synchronizer ring does not lock, replace the synchronizer ring.


d.
C113624

Using a feeler gauge, measure the clearance between the synchronizer ring back and reverse driven gear spline end.

Standard clearance:

0.68 to 1.32 mm (0.0268 to 0.0519 in.)


Minimum clearance:

0.68 mm (0.0268 in.)


If the clearance is less than the minimum, replace the reverse driven gear synchronizer ring set.


Hide 33395 44.INSPECT NO. 3 TRANSMISSION HUB SLEEVE

a.
C116325
2.703,1.84 2.848,1.996 0.145,0.156 10 A 1.335,1.81 1.48,1.966 0.145,0.156 10 B

Using a vernier caliper, measure the clearance between the No. 3 transmission hub sleeve and the No. 3 gear shift fork.

Standard clearance (A - B):

0.10 to 0.50 mm (0.00394 to 0.0196 in.)


If the clearance is not as specified, replace the No. 3 transmission hub sleeve and No. 3 gear shift fork.


Hide 33327 45.INSPECT NO. 4 TRANSMISSION HUB SLEEVE

a.
C116326
1.372,1.812 1.52,1.981 0.148,0.169 10 A 2.938,1.821 3.086,1.99 0.148,0.169 10 B

Using a vernier caliper, measure the clearance between the No. 4 transmission hub sleeve and the reverse shift fork.

Standard clearance (A - B):

0.15 to 0.41 mm (0.00591 to 0.0161 in.)


If the clearance is not as specified, replace the No. 4 transmission hub sleeve and reverse shift fork.