Home › Drivetrain › EA64F MANUAL TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › 2012.12–2014.10
RM3090E _52 Drivetrain _008756 EA64F MANUAL TRANSMISSION / TRANSAXLE _0048565 DIFFERENTIAL CASE A

EA64F MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41331F 1.INSTALL FRONT DIFFERENTIAL SIDE GEAR

a.
C278055

Coat the rotating surface of the front differential side gear with gear oil.


b.

Install the 2 front differential side gears and 2 front differential side gear thrust washers to the front differential case.


Hide 41341F 2.INSTALL FRONT DIFFERENTIAL PINION

a.
C278053

Coat the rotating surface of the front differential pinion with gear oil.


b.

Install the 2 front differential pinion thrust washers and 2 front differential pinions to the front differential case.

HINT:

Install the 2 front differential pinions with the front differential washers while turning the front differential pinion.



c.
C278052

Install the No. 1 front differential pinion shaft into the front differential case.


d.
C278056

Using a 5 mm pin punch and hammer, install the front differential pinion shaft straight pin through the front differential case and the hole in the No. 1 front differential pinion shaft.


e.
C278057

Using a hammer and chisel, caulk the pin holes around the circumference of the front differential case.


Hide 41221 3.INSTALL FRONT DIFFERENTIAL RING GEAR

a.

Clean the contact surfaces of the front differential case and front differential ring gear.


b.

Heat the front differential ring gear to 90 to 110°C (194 to 230°F) in boiling water.


c.
C278049C01
1.688,1.573 0.542,0.802 0.542,0.802 1.677,1.5 true 0.208,0.667 0.521,0.865 0.313,0.198 10 *a
*a Matchmark


After the moisture on the ring gear has completely evaporated, quickly align the matchmarks on the front differential ring gear and the front differential case and install the front differential ring gear to the front differential case.


d.

Install the 16 bolts.

Torque:
106 N*m (1081 kgf*cm, 78 ft.*lbf)


Hide 41311E 4.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C204252N01
0.561,1.795 0.873,1.939 0.313,0.145 10 SST 0.935,1.875 1.263,1.875 false 1.314,2.243 1.096,2.243 false 1.096,2.243 1.096,1.875 false

Using SST and a press, press in a new front differential case front tapered roller bearing.

SST
09316-20011  09513-36040  


Hide 41311F 5.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

C133923C01
1.531,0.854 1.219,0.438 1.219,0.438 1.042,0.438 false 1.938,0.063 2.323,0.063 false 0.729,0.354 1.063,0.521 0.333,0.167 10 SST 2.375,0 2.688,0.188 0.313,0.188 10 *a
*a Press


a.

Using SST and a press, press in a new rear tapered roller bearing.

SST
09554-22010  


Hide 43410M 6.INSTALL FRONT DIFFERENTIAL CASE OIL SEAL

a.

Coat the lip of a new front differential case oil seal with MP grease.


b.
C318265C01
2.406,0.375 2.906,0.469 2.906,0.469 2.521,0.802 true 1.542,0.635 1.854,0.833 0.313,0.198 10 false *a 2.969,0.406 3.281,0.604 0.313,0.198 10 false SST
*a 21.5 to 22.5 mm (0.847 to 0.885 in.)


Using SST and a hammer, tap in a new front differential case oil seal to the front differential case.

SST
09950-60010  (09951-00410)
09950-70010  (09951-07200)

Standard depth:

21.5 to 22.5 mm (0.847 to 0.885 in.)


NOTICE:

Do not damage the front differential case oil seal lip.