Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › SFI SYSTEM › 2012.12–2015.04
RM3090E _51 Engine / Hybrid System _008381 3ZR-FAE ENGINE CONTROL _0048627 SFI SYSTEM C

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  P1047  Valvematic Driver Learned Value Error / Power Source Circuit Malfunction Bank 1  


DESCRIPTION

The EDU in the continuously variable valve lift controller assembly learns and stores the actuator position in memory.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1047 Valvematic Driver Learned Value Error / Power Source Circuit Malfunction Bank 1 The power supply to the continuously variable valve lift controller assembly is cut and the continuously variable valve lift controller internal EDU actuator position learned value cannot be learned or is abnormal (1 trip detection logic).
·

Continuously variable valve lift controller power source circuit

·

Continuously variable valve lift controller assembly


Comes on DTC stored

MONITOR DESCRIPTION

If the actuator position learned value is abnormal or cannot be learned due to a continuously variable valve lift controller assembly power supply problem or similar malfunction, DTC P1047 is stored. Also, when a VALVEMATIC system malfunction is detected, the power supply to the continuously variable valve lift controller assembly is cut as a fail-safe function and DTC P1047 is stored.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Start the engine and warm it up.

3.

Turn the GTS on.

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine and idle it for 20 seconds.

7.

Turn the GTS on.

9.

Turn the ignition switch off and wait for at least 30 seconds.

10.

Start the engine and idle it for 20 seconds.

11.

Turn the ignition switch off and wait for at least 30 seconds.

12.

Turn the ignition switch to ON.

13.

Turn the GTS on.

14.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

15.

Read the DTCs.


WIRING DIAGRAM

A298881E01
1.167,1.708 2.24,1.906 1.073,0.198 10 false Battery 3.958,1.094 5.031,1.292 1.073,0.198 10 false VLVMATIC 5.719,0.938 6.146,1.135 0.427,0.198 10 false +B 5.365,1.813 5.792,2.01 0.427,0.198 10 false B46 5.521,0.802 5.698,1 0.177,0.198 10 false 1 5.354,1.99 7.135,2.365 1.781,0.375 10 false Continuously Variable Valve Lift Controller Assembly 1.99,1.104 3.063,1.302 1.073,0.198 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When one of the following DTCs is stored and the MIL is illuminated, DTC P1047 is stored and actuator position learning is performed every time the engine is started. Also, after the system returns to normal, the following occurs during the first driving cycle: 1) DTC P1047 is stored, 2) actuator position learning is performed and 3) the MIL illuminates during actuator position learning.

Actuator position learning is performed when these DTCs are output.
P1046, P1049, P104A, P1055, P2646, P2647, P2648, P2649, P264A, U011B



HINT:
·

When there is no power (+B) supplied to the continuously variable valve lift controller assembly, DTC U011B is stored. After the continuously variable valve lift controller assembly power supply system and communication lines have been connected or repaired, actuator position learning is performed and DTC P1047 is stored the next time the vehicle is driven.

·

After performing repairs, perform the confirmation driving pattern and check that DTCs are not output again.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.PERFORM SIMULATION TEST
a.

Perform the simulation test

i.

Drive the vehicle in accordance with the driving pattern described in Confirmation driving Pattern.



b.

Check if the MIL is illuminated during idling after clearing the DTCs in the above simulation test.

Result:
Result Proceed to
MIL illuminate A
MIL does not illuminate B


HINT:

If the ignition switch is turned to ON while the actuator position learning is incomplete or when learning has not been performed, DTC P1047 is output.




A

2.CHECK ANY OTHER DTCS OUTPUT

B

END

2.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs.

Result:
Result Proceed to
DTC P1047 is output A
DTC P1047 and other DTCs are output B




A

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY)

B

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY)
a.
A206538C01
0.292,0.917 0.667,1.208 0.375,0.292 1.521,1.26 0.938,1.792 true 0.073,0.052 0.26,0.219 0.188,0.167 10 *a 0.698,1.792 0.906,1.948 0.208,0.156 10 +B 0.344,0.979 0.719,1.208 0.375,0.229 10 B46
*a Front view of wire harness connector
(to Continuously Variable Valve Lift Controller Assembly)


Disconnect the continuously variable valve lift controller assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B46-1 (+B) - Body ground Ignition switch ON 11 to 14 V


HINT:

Perform "Inspection After Repair" after replacing the continuously variable valve lift controller assembly (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).



Result:
Proceed to
OK
NG



OK

REPLACE CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY - BATTERY)