Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › SFI SYSTEM › 2012.12–2015.04
RM3090E _51 Engine / Hybrid System _008381 3ZR-FAE ENGINE CONTROL _0048627 SFI SYSTEM C

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  P0107  Manifold Absolute Pressure / Barometric Pressure Circuit Low Input  P0108  Manifold Absolute Pressure / Barometric Pressure Circuit High Input  


DESCRIPTION

The manifold absolute pressure sensor detects pressure inside the intake manifold as an absolute pressure with a built-in sensor and outputs a voltage. Based on the voltage from the manifold absolute pressure sensor, the ECM controls the purge VSV and corrects any errors in the air fuel ratio due to change in pressure.

A263608E01
0.093,2.233 0.314,2.396 0.221,0.163 10 1.0 0.093,2.079 0.314,2.24 0.221,0.161 10 1.2 0.093,1.652 0.323,1.809 0.23,0.156 10 2.4 0.093,1.174 0.312,1.33 0.219,0.156 10 3.6 0.093,0.929 0.326,1.085 0.233,0.156 10 4.2 0.91,3.579 1.168,3.744 0.259,0.165 10 150 1.543,3.372 1.8,3.524 0.257,0.152 10 450 2.141,3.372 2.391,3.525 0.25,0.153 10 750 0.74,3.372 0.99,3.525 0.25,0.153 10 100 2.52,3.372 2.818,3.523 0.299,0.151 10 900 0.162,0.212 0.967,0.41 0.806,0.198 10 Voltage (V) 0.486,3.999 2.244,4.192 1.758,0.193 10 Manifold Absolute Pressure 2.489,3.585 3.232,3.786 0.743,0.201 10 mmHg(abs) 2.719,2.951 3.302,3.131 0.583,0.179 10 kPa(abs) 0.798,2.999 1.245,3.151 0.448,0.152 10 19.998 0.504,2.744 0.952,2.895 0.448,0.152 10 13.332 1.422,2.743 1.87,2.895 0.448,0.152 10 59.995 2.009,2.999 2.457,3.151 0.448,0.152 10 99.992 2.319,2.749 2.871,2.901 0.552,0.152 10 119.990

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input The output voltage from the manifold absolute pressure sensor below 0.5 V for 0.5 seconds (1 trip detection logic).
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored
P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input The output voltage from the manifold absolute pressure sensor higher than 4.5 V for 0.5 seconds (1 trip detection logic).
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored

HINT:

When either of these DTCs is output, check the manifold absolute pressure using the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAP.


Manifold Absolute Pressure Malfunction
Approximately 0 kPa(abs) [0 mmHg(abs)]
·

Short in PIM circuit to ground

·

Short in PIM circuit to EPIM circuit

·

Open in VCPM circuit


130 kPa(abs) [975 mmHg(abs)] or higher
·

Short in VCPM circuit to PIM circuit

·

Open in PIM circuit

·

Open in EPIM circuit



MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the manifold absolute pressure. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the manifold pressure sensor and stores a DTC.

Example:

When the sensor output voltage remains below 0.5 V, or higher than 4.5 V for more than 0.5 seconds, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

8.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0107 or P0108.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A256088E09
0.313,2.938 2.083,3.302 1.771,0.365 10 Manifold Absolute Pressure Sensor 1.469,0.906 1.688,1.073 0.219,0.167 10 VC 1.771,0.802 1.865,0.969 0.094,0.167 10 3 1.771,1.49 1.865,1.656 0.094,0.167 10 2 1.771,2.271 1.865,2.438 0.094,0.167 10 1 4.333,0.802 4.594,0.969 0.26,0.167 10 118 4.385,1.49 4.583,1.667 0.198,0.177 10 87 4.323,2.271 4.594,2.438 0.271,0.167 10 119 4.677,0.802 5.104,1 0.427,0.198 10 VCPM 4.677,1.49 5,1.677 0.323,0.188 10 PIM 4.677,2.271 5.083,2.438 0.406,0.167 10 EPIM 1.417,1.604 1.688,1.771 0.271,0.167 10 PIM 1.5,2.365 1.688,2.531 0.188,0.167 10 E2 0.313,2.771 0.615,2.927 0.302,0.156 10 B45 5.667,0.552 6.021,0.719 0.354,0.167 10 5 V 5.083,3.188 6.552,3.5 1.469,0.313 10 ECM 5.094,3.01 5.427,3.177 0.333,0.167 10 B75

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (MAP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAP.

Powertrain > Engine and ECT > Data List
Tester Display
MAP
50003 234 4

e.

Read the MAP value.

OK:

Same value as the actual atmospheric pressure.



HINT:
·

Standard atmospheric pressure is 101 kPa(abs) (758 mmHg(abs)). For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa(abs) (7.5 mmHg(abs)). Varies by weather (high atmospheric pressure, low atmospheric pressure).

·

Also, check "Atmosphere Pressure" in the Data List.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.
A208640C02
0.344,0.99 0.792,1.302 0.448,0.313 1.417,1.333 1.167,1.844 true 2.01,1.333 2.344,1.865 true 1.854,1.875 1.781,1.323 true 0.094,0.063 0.24,0.229 0.146,0.167 10 *a 0.427,1.063 0.823,1.219 0.396,0.156 10 B45 1.052,1.885 1.271,2.052 0.219,0.167 10 E2 2.281,1.885 2.542,2.042 0.26,0.156 10 VC 1.74,1.906 2.094,2.083 0.354,0.177 10 PIM
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage between the terminals of the manifold absolute pressure sensor connector.

Standard Voltage:
Tester Connection Condition Specified Condition
B45-3 (VC) - B45-1 (E2) Ignition switch ON 4.75 to 5.25 V
B45-2 (PIM) - B45-1 (E2) Ignition switch ON 3.0 to 5.25 V



Result:
Proceed to
OK
NG



OK

3.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

5.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
3.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0107 OR P0108)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0107 OR P0108)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

j.

Read the DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P0107 or P0108 is output B



A

END

B

5.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B45-3 (VC) - B75-118 (VCPM) Always Below 1 Ω
B45-1 (E2) - B75-119 (EPIM) Always Below 1 Ω
B45-2 (PIM) - B75-87 (PIM) Always Below 1 Ω
B45-3 (VC) or B75-118 (VCPM) - Body ground Always 10 kΩ or higher
B45-2 (PIM) or B75-87 (PIM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR