Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination assembly meter via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connectors are disconnected from the skid control ECU (brake actuator assembly).

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter assembly and the skid control ECU (brake actuator assembly).

·

The ABS control system is defective.


HINT:

In some cases, the GTS cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM

C279160E01
5.479,3.948 7.115,4.354 1.635,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 5.51,3.76 5.969,3.958 0.458,0.198 10 false A64 1.75,0.906 2.344,1.083 0.594,0.177 10 false CAN I/F 0.802,0.948 1.26,1.146 0.458,0.198 10 false CPU 1.115,2.281 1.573,2.479 0.458,0.198 10 false ABS 1.802,2.844 2.115,3.042 0.313,0.198 10 false IG 4.406,2.917 5.469,3.115 1.063,0.198 10 false ECU-IG NO. 3 2.99,2.74 4.073,2.938 1.083,0.198 10 false from IG Circuit 2.583,2.292 4.552,2.479 1.969,0.188 10 false Engine Stop and Start ECU*2 2.604,2.083 2.927,2.25 0.323,0.167 10 false G87 3.313,1.594 3.688,1.792 0.375,0.198 10 false IGO1 3.771,1.469 4.083,1.667 0.313,0.198 10 false 12 5.927,2.708 6.385,2.906 0.458,0.198 10 false IG1 5.604,2.865 5.917,3.063 0.313,0.198 10 false 34 5.896,3.292 6.51,3.49 0.615,0.198 10 false GND1 5.646,3.417 5.823,3.635 0.177,0.219 11 false 1 0.531,3.396 2.448,3.615 1.917,0.219 10 false Combination Meter Assembly 1.146,4.333 2.854,4.563 1.708,0.229 10 false : CAN Communication Line 2.792,3.448 4.74,3.656 1.948,0.208 10 false *1: w/o Stop and Start System 2.823,3.802 4.667,4 1.844,0.198 10 false *2: w/ Stop and Start System 5.146,2.615 5.458,2.813 0.313,0.198 10 false *1 5.552,2.198 5.74,2.365 0.188,0.167 10 false *2 2.833,4.146 3.646,4.344 0.813,0.198 10 false *3: for LHD 2.844,4.448 3.813,4.667 0.969,0.219 10 false *4: for RHD 4.281,1.521 4.698,1.698 0.417,0.177 10 false *2, *3 4.844,1.844 5.271,2.01 0.427,0.167 10 false *2, *4

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

2.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output (for LHD)
DTC is output (for RHD)



DTC is not output

3.INSPECT BATTERY

DTC is output (for LHD)

DTC is output (for RHD)

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG (for 1AD-FTV)
NG (for 2AD-FHV)
NG (for 2AD-FTV)
NG (for 2AR-FE)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)




OK

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG (for 1AD-FTV)

NG (for 2AD-FHV)

NG (for 2AD-FTV)

NG (for 2AR-FE)

NG (for 3ZR-FAE)

NG (for 3ZR-FE)

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.
C199357C49
1.625,0.083 2,0.333 0.375,0.25 2.219,1.854 2.292,1.406 false 0,0 0.313,0.156 0.313,0.156 10 false *a 1.688,0.125 2.146,0.323 0.458,0.198 10 false A64 2.135,1.875 2.427,2.073 0.292,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A64 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A64-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

NG (w/ Stop and Start System)

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.
C199357C53
1.625,0.083 2,0.333 0.375,0.25 0.615,1.771 1.052,0.99 false 0,0 0.313,0.156 0.313,0.156 10 false *a 1.688,0.125 2.146,0.323 0.458,0.198 10 false A64 0.448,1.823 0.906,2.021 0.458,0.198 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING GTS (ABS WARNING LIGHT)
a.

Reconnect the A64 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light OFF or ON OFF: Warning light off
ON: Warning light on
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
ABS Warning Light
50003 105 51
g.

Check the GTS display condition of the ABS warning light.

Result:
Proceed to
Display of the Data List remains OFF
Display of the Data List remains ON




Display of the Data List remains OFF

Display of the Data List remains ON