Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1241  Low Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or generator circuit, etc.

The DTC is canceled when the IG1 terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1241 Low Power Supply Voltage Malfunction When any of the following is detected:
1.

At a vehicle speed of 3 km/h (2 mph) or more, the IG1 terminal voltage is less than 9.5 V for 10 seconds or more.

2.

When the solenoid relay remains ON and the IG1 terminal voltage is less than 9.5 V, the relay contact is open for 0.22 seconds or more.

3.

With the IG1 terminal voltage 9.5 V or less, the vehicle speed sensor power supply decreases for 60 seconds or more.

4.

When the motor fail safe relay is ON after the motor relay turns ON, the IG1 terminal voltage is 9.5 V or less and the actuator pump drive motor is OFF for 0.22 seconds or more.


·

ECU-IG NO. 3 fuse

·

Battery

·

Charging system

·

Backup boost converter circuit (w/ Stop and Start System)

·

Power source circuit

·

Internal power supply circuit of the skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C279050E01
5.302,3.594 5.76,3.792 0.458,0.198 10 false A64 5.292,3.792 6.823,4.188 1.531,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 0.906,3.563 1.365,3.76 0.458,0.198 10 false G87 0.875,3.75 2.875,3.969 2,0.219 10 false Engine Stop and Start ECU*2 1.656,1.75 2.01,1.948 0.354,0.198 10 false IGO1 2.177,1.635 2.406,1.823 0.229,0.188 10 false 12 3.448,1.021 4.406,1.219 0.958,0.198 10 false ECU-IG NO. 3 5.281,0.75 5.542,0.938 0.26,0.188 10 false 34 5.552,0.854 6.01,1.052 0.458,0.198 10 false IG1 5.333,2.917 5.573,3.094 0.24,0.177 10 false 1 5.563,3.031 6.021,3.229 0.458,0.198 10 false GND1 4.594,0.969 4.906,1.167 0.313,0.198 10 false *1 3.521,1.667 3.99,1.854 0.469,0.188 10 false *2, *3 4.135,2.375 4.552,2.552 0.417,0.177 10 false *2, *4 1.979,0.865 2.969,1.052 0.99,0.188 10 false from IG1 Circuit 0.396,4.125 2.333,4.313 1.938,0.188 10 false *1: w/o Stop and Start System 0.438,4.458 2.323,4.646 1.885,0.188 10 false *2: w/ Stop and Start System 2.573,4.125 3.292,4.302 0.719,0.177 10 false *3: for LHD 2.573,4.438 3.344,4.615 0.771,0.177 10 false *4: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG (for 1AD-FTV)
NG (for 2AD-FHV)
NG (for 2AD-FTV)
NG (for 2AR-FE)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)




OK

2.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG (for 1AD-FTV)

NG (for 2AD-FHV)

NG (for 2AD-FTV)

NG (for 2AR-FE)

NG (for 3ZR-FAE)

NG (for 3ZR-FE)

2.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.

Make sure that there is no looseness in the locking part and connecting part of the connectors.


b.
C199357C49
1.625,0.083 2,0.333 0.375,0.25 2.219,1.854 2.292,1.406 false 0,0 0.313,0.156 0.313,0.156 10 false *a 1.688,0.125 2.146,0.323 0.458,0.198 10 false A64 2.135,1.875 2.427,2.073 0.292,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A64 skid control ECU (brake actuator assembly) connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A64-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

NG (w/ Stop and Start System)

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.
C199357C53
1.625,0.083 2,0.333 0.375,0.25 0.615,1.771 1.052,0.99 false 0,0 0.313,0.156 0.313,0.156 10 false *a 1.688,0.125 2.146,0.323 0.458,0.198 10 false A64 0.448,1.823 0.906,2.021 0.458,0.198 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

4.RECONFIRM DTC
a.

Reconnect the A64 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


e.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
DTC C1241 is not output
DTC C1241 is output



DTC C1241 is not output

DTC C1241 is output