Refer to DTCs C1273, C1274, C1403 and C1404.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1273
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1277 | Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) | Detected only during Test Mode. | ·
Rear speed sensor RH (for 4WD/AWD) ·
Rear speed sensor RH (Rear axle hub and bearing assembly RH) (for 2WD) ·
Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH) |
| C1278 | Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) | Detected only during Test Mode. | ·
Rear speed sensor LH (for 4WD/AWD) ·
Rear speed sensor LH (Rear axle hub and bearing assembly LH) (for 2WD) ·
Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH) |
| C1415 | Rear Speed Sensor RH Output Malfunction | Any of the following is detected:
1.
An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more. 2.
At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds. 3.
At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more. |
·
Rear speed sensor RH (for 4WD/AWD) ·
Rear speed sensor RH (Rear axle hub and bearing assembly RH) (for 2WD) ·
Rear speed sensor RH circuit ·
Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH) ·
Skid control ECU (Brake actuator assembly) |
| C1416 | Rear Speed Sensor LH Output Malfunction | Any of the following is detected:
1.
An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more. 2.
At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds. 3.
At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more. |
·
Rear speed sensor LH (for 4WD/AWD) ·
Rear speed sensor LH (Rear axle hub and bearing assembly LH) (for 2WD) ·
Rear speed sensor LH circuit ·
Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH) ·
Skid control ECU (Brake actuator assembly) |
DTC C1415 and C1277 are for the rear speed sensor RH.
DTC C1416 and C1278 are for the rear speed sensor LH.
Refer to DTCs C1273, C1274, C1403 and C1404.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1273
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited (for 2WD).
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Speed Open | Rear speed sensor open RH detection | Normal or Error | Normal | Error: Momentary interruption |
| RL Speed Open | Rear speed sensor LH open detection | Normal or Error | Normal | Error: Momentary interruption |
| Tester Display |
|---|
| RR Speed Open |
| RL Speed Open |
Perform the above inspection before removing the sensor and connector.
There are no momentary interruptions.
| Proceed to |
|---|
| OK |
| NG (for 2WD) |
| NG (for 4WD/AWD) |
OK
NG (for 2WD)
NG (for 4WD/AWD)
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed:
No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed:
No large fluctuations |
| Tester Display |
|---|
| RR Wheel Speed |
| RL Wheel Speed |
Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK
The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Tester Display |
|---|
| Signal Check |
All Test Mode DTCs are cleared.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| DTCs C1415 and C1416 are not output |
| DTCs C1415 and/or C1416 are output (for 2WD) |
| DTCs C1415 and/or C1416 are output (for 4WD/AWD) |
DTCs C1415 and C1416 are not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTCs C1415 and/or C1416 are output (for 2WD)
DTCs C1415 and/or C1416 are output (for 4WD/AWD)
Turn the ignition switch off.
| *a | Normal |
| *b | Abnormal |
| *c | Clearance |
for 2WD:
Check the speed sensor installation.
There is no clearance between the sensor and the rear axle hub.
Because the rear axle hub and bearing assembly cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly.
| *a | Normal |
| *b | Abnormal |
| *c | Clearance |
for 4WD/AWD:
Check the rear speed sensor installation.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR(for 4WD/AWD)>INSTALLATION
There is no clearance between the sensor and the rear axle carrier.
The installation bolt is tightened properly.
| Proceed to |
|---|
| OK (for 2WD) |
| OK (for 4WD/AWD) |
| NG (for 2WD) |
| NG (for 4WD/AWD) |
OK (for 2WD)
OK (for 4WD/AWD)
NG (for 2WD)
NG (for 4WD/AWD)
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
for RH:
Disconnect the m1 and mM1 skid control sensor wire connectors.
for LH:
Disconnect the n1 and nN1 skid control sensor wire connectors.
| *A | for RH |
| *B | for LH |
| *a | Front view of Skid Control Sensor Wire |
| *b | Front view of wire harness connector
(to Sensor Side Connector) |
| *c | Front view of wire harness connector
(to Vehicle Side Connector) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| m1-2 (+) - mM1-1 | Always | Below 1 Ω |
| m1-1 (-) - mM1-2 | Always | Below 1 Ω |
| m1-2 (+) - mM1-2 | Always | 10 kΩ or higher |
| m1-2 (+) or mM1-1 - Body ground | Always | 10 kΩ or higher |
| m1-1 (-) - mM1-1 | Always | 10 kΩ or higher |
| m1-1(-) or mM1-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| n1-2 (+) - nN1-1 | Always | Below 1 Ω |
| n1-1 (-) - nN1-2 | Always | Below 1 Ω |
| n1-2 (+) - nN1-2 | Always | 10 kΩ or higher |
| n1-2 (+) or nN1-1 - Body ground | Always | 10 kΩ or higher |
| n1-1 (-) - nN1-1 | Always | 10 kΩ or higher |
| n1-1 (-) or nN1-2 - Body ground | Always | 10 kΩ or higher |
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speed sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR(for 4WD/AWD)>REMOVAL
Check the speed sensor tip.
No scratches, oil, or foreign matter on the sensor tip.
If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.
Check the speed sensor signal after cleaning or replacement.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear axle hub and bearing assembly.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL
Check the speed sensor rotor.
No scratches, oil, or foreign matter on the rotors.
Check the speed sensor signal after cleaning or replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.
Reinstall the rear speed sensor and rear axle hub and bearing assembly.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR(for 4WD/AWD)>INSTALLATION for the rear speed sensor
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>INSTALLATION for the rear axle hub and bearing assembly
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 2WD:
Reconnect the mM1 and/or nN1 skid control sensor wire connector.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A64 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-17 (RR+) - m1-2 (+) | Always | Below 1 Ω |
| A64-16 (RR-) - m1-1 (-) | Always | Below 1 Ω |
| A64-17 (RR+) or m1-2(+) - Body ground | Always | 10 kΩ or higher |
| A64-16 (RR-) or m1-1 (-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-5 (RL+) - n1-2 (+) | Always | Below 1 Ω |
| A64-4 (RL-) - n1-1 (-) | Always | Below 1 Ω |
| A64-5 (RL+) or n1-2 (+) - Body ground | Always | 10 kΩ or higher |
| A64-4 (RL-) or n1-1 (-) - Body ground | Always | 10 kΩ or higher |
for 4WD/AWD:
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A64 skid control ECU (brake actuator assembly) connector and the N11 and/or M20 rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-17 (RR+) - M20-1 (RR+) | Always | Below 1 Ω |
| A64-16 (RR-) - M20-2 (RR-) | Always | Below 1 Ω |
| A64-17 (RR+) or M20-1(RR+) - Body ground | Always | 10 kΩ or higher |
| A64-16 (RR-) or M20-2 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-5 (RL+) - N11-1 (RL+) | Always | Below 1 Ω |
| A64-4 (RL-) - N11-2 (RL-) | Always | Below 1 Ω |
| A64-5 (RL+) or N11-1 (RL+) - Body ground | Always | 10 kΩ or higher |
| A64-4 (RL-) or N11-2 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 2WD:
Reconnect the A64 skid control ECU (brake actuator assembly) connector.
Turn the ignition switch to ON.
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector
(to Rear Speed Sensor) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| m1-2 (+) - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| n1-2 (+) - Body ground | Ignition switch ON | 8 to 14 V |
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
for 4WD/AWD:
Reconnect the A64 skid control ECU (brake actuator assembly) connector.
Turn the ignition switch to ON.
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector
(to Rear Speed Sensor) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M20-1 (RR+) - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N11-1 (RL+) - Body ground | Ignition switch ON | 8 to 14 V |
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
for 2WD:
Reconnect the m1 and/or n1 rear speed sensor connector.
for 4WD/AWD:
Reconnect the N11 and/or M20 rear speed sensor connector.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| DTCs C1415 and C1416 are not output |
| DTCs C1415 and/or C1416 are output (for 2WD) |
| DTCs C1415 and/or C1416 are output (for 4WD/AWD) |
DTCs C1415 and C1416 are not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTCs C1415 and/or C1416 are output (for 2WD)
DTCs C1415 and/or C1416 are output (for 4WD/AWD)
Turn the ignition switch off.
Replace the rear speed sensor and sensor rotor (rear axle hub and bearing assembly).
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| DTCs C1415 and C1416 are not output |
| DTCs C1415 and/or C1416 are output |
DTCs C1415 and C1416 are not output
DTCs C1415 and/or C1416 are output
Turn the ignition switch off.
Replace the rear speed sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR(for 4WD/AWD)>REMOVAL
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| DTCs C1415 and C1416 are not output |
| DTCs C1415 and/or C1416 are output |
DTCs C1415 and C1416 are not output
DTCs C1415 and/or C1416 are output
Turn the ignition switch off.
Replace the rear speed sensor rotor (rear axle hub and bearing assembly).
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL
The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| DTCs C1413 and C1414 are not output |
| DTCs C1413 and/or C1414 are output |
DTCs C1413 and C1414 are not output
DTCs C1413 and/or C1414 are output