Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1281  Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)  C1421  Open or Short in Master Cylinder Pressure Sensor  C1423  Master Cylinder Pressure Sensor Zero Point Low Malfunction  C1424  Master Cylinder Pressure Sensor Output Malfunction  


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU (brake actuator assembly).

C234442E06
4.969,3.771 6.594,3.948 1.625,0.177 10 false Brake Actuator Assembly 0.188,1.844 1.583,2.219 1.396,0.375 10 false from Stop Light Switch Assembly 2.802,1.823 3.25,2.031 0.448,0.208 10 false STP 3.854,1.5 4.323,1.708 0.469,0.208 10 false VCM 3.896,2.198 4.344,2.406 0.448,0.208 10 false PMC 3.969,2.906 4.281,3.125 0.313,0.219 10 false E2 0.229,4.073 3.896,4.281 3.667,0.208 10 false VCM: Power Supply for Master Cylinder Pressure Sensor 0.365,4.833 3.302,5.229 2.938,0.396 10 false E2: Master Cylinder Pressure Sensor Ground 2.99,0.594 4.125,0.75 1.135,0.156 10 false Skid Control ECU 5.448,1.792 6.49,2.542 1.042,0.75 10 false Master Cylinder Pressure Sensor 0.229,4.469 3.156,4.677 2.927,0.208 10 false PMC: Master Cylinder Pressure Sensor Input

DTC No. Detection Item DTC Detection Condition Trouble Area
C1281 Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC) Detected only during Test Mode. Brake actuator assembly (Master cylinder pressure sensor)
C1421 Open or Short in Master Cylinder Pressure Sensor Either of the following is detected:
1.

With the IG1 terminal voltage between 9.5 and 17.4 V, the VCM terminal voltage is not between 4.4 and 5.6 V for 1.2 seconds or more.

2.

When the VCM terminal voltage is between 4.8 and 5.2 V, the PMC terminal voltage is not between 0.19 and 4.57 V for 1.2 seconds or more.


Brake actuator assembly (Master cylinder pressure sensor)
C1423 Master Cylinder Pressure Sensor Zero Point Low Malfunction The PMC terminal voltage is less than 0.27 V for 5 seconds or more. Brake actuator assembly (Master cylinder pressure sensor)
C1424 Master Cylinder Pressure Sensor Output Malfunction Any of the following is detected:
1.

Noise occurs in the PMC terminal 7 times or more within 5 seconds.

2.

When the vehicle speed drops from 40 km/h (25 mph) to 10 km/h (6 mph), the master cylinder pressure does not change by at least 0.048 MPa.

3.

At a vehicle speed of 7 km/h (4.3 mph) or more, the PMC terminal voltage is between 0.86 and 1.0 V and does not change by at least 0.048 MPa for 60 seconds or more.

4.

At a vehicle speed of 7 km/h (4.3 mph) or more, the PMC terminal voltage is 1.0 V or more and does not change by at least 0.048 MPa for 30 seconds or more.

5.

At a vehicle speed of 7 km/h (4.3 mph) or more with the stop switch ON, a state in which the pressure sensor input value is sufficiently greater than the estimated master pressure continues for 1 second or more and this state occurs 5 or more times each time the ignition switch is turned to ON, and this occurs 8 or more times consecutively.


Brake actuator assembly (Master cylinder pressure sensor)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.REPLACE BRAKE ACTUATOR ASSEMBLY
a.

Replace the brake actuator assembly (master cylinder pressure sensor).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/ VSC)>REMOVAL

Result:
Proceed to
NEXT




NEXT

END