The skid control ECU (brake actuator assembly) receives signals from the ECM via the CAN communication system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1437 | Lost Communication with ECM | When the IG1 terminal voltage is 10 V or more and the vehicle speed is 15 km/h (9 mph) or more, data cannot be sent to the ECM for 2 seconds or more. | ·
CAN communication system (skid control ECU to ECM) ·
Skid control ECU (brake actuator assembly) |
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| EFI Communication Open | EFI communication open detection | Normal or Error | Normal | Error: Momentary interruption |
| Tester Display |
|---|
| EFI Communication Open |
Perform the above inspection before removing the sensor and connector.
There are no momentary interruptions.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.
Check that no CAN communication system DTC is output.
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC C1437 is not output |
| DTC C1437 is output |
| CAN communication system DTC is output (for LHD) |
| CAN communication system DTC is output (for RHD) |
DTC C1437 is not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTC C1437 is output
CAN communication system DTC is output (for LHD)
CAN communication system DTC is output (for RHD)
Turn the ignition switch off.
Repair or replace the harness or connector.
Check for any momentary interruption between the skid control ECU (brake actuator assembly) and the ECM.
Check that there is no momentary interruption.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Clear the DTCs
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.
Check that no CAN communication system DTC is output.
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC is not output |
| DTC is output |
| CAN communication system DTC is output (for LHD) |
| CAN communication system DTC is output (for RHD) |
DTC is not output
DTC is output
CAN communication system DTC is output (for LHD)
CAN communication system DTC is output (for RHD)