Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › 2012.12–2016.08
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048747 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the radio receiver assembly through this circuit.

The sound signal that has been sent is amplified by the radio receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly or speakers.

WIRING DIAGRAM

E229861E38
0.813,0.813 1.24,0.969 0.427,0.156 10 AUXO 0.896,1.281 1.323,1.438 0.427,0.156 10 ARO 0.938,1.75 1.365,1.906 0.427,0.156 10 ALO 0.813,2.229 1.24,2.385 0.427,0.156 10 ASGN 0.813,2.708 1.24,2.865 0.427,0.156 10 AGND 2.552,2.844 3.323,3.083 0.771,0.24 10 Shielded 4.063,2.865 4.719,3.021 0.656,0.156 10 Shielded 5.927,0.729 6.354,0.885 0.427,0.156 10 ADPG 5.927,1.219 6.354,1.375 0.427,0.156 10 VAR+ 5.688,0.677 5.865,0.833 0.177,0.156 10 25 5.698,1.167 5.875,1.323 0.177,0.156 10 26 5.698,1.625 5.875,1.781 0.177,0.156 10 28 5.698,2.115 5.875,2.271 0.177,0.156 10 27 5.698,2.583 5.875,2.74 0.177,0.156 10 11 1.323,0.688 1.5,0.844 0.177,0.156 10 8 1.323,1.146 1.5,1.302 0.177,0.156 10 5 1.323,1.615 1.5,1.771 0.177,0.156 10 6 1.323,2.083 1.5,2.24 0.177,0.156 10 7 1.323,2.594 1.5,2.75 0.177,0.156 10 9 0.438,3.219 0.792,3.375 0.354,0.156 10 G145 0.417,3.385 1.604,3.781 1.188,0.396 10 No. 1 Stereo Jack Adapter Assembly 5.802,3.354 6.771,3.708 0.969,0.354 10 Radio Receiver Assembly 5.927,1.667 6.354,1.823 0.427,0.156 10 VAL+ 5.927,2.177 6.354,2.333 0.427,0.156 10 VA- 5.927,2.635 6.354,2.792 0.427,0.156 10 AGND 5.802,3.177 6.313,3.365 0.51,0.188 10 G48

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the G48 radio receiver assembly connector.


b.

Disconnect the G145 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G145-8 (AUXO) - G48-25 (ADPG) Always Below 1 Ω
G145-5 (ARO) - G48-26 (VAR+) Always Below 1 Ω
G145-6 (ALO) - G48-28 (VAL+) Always Below 1 Ω
G145-7 (ASGN) - G48-27 (VA-) Always Below 1 Ω
G145-9 (AGND) - G48-11 (AGND) Always Below 1 Ω
G145-8 (AUXO) - Body ground Always 10 kΩ or higher
G145-5 (ARO) - Body ground Always 10 kΩ or higher
G145-6 (ALO) - Body ground Always 10 kΩ or higher
G145-7 (ASGN) - Body ground Always 10 kΩ or higher
G145-9 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR