Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2012.12–2013.11
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) D

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  OPERATION CHECK  


CHECK PANEL&STEERING SWITCH


HINT:
·

The radio and display receiver assembly panel switches and steering switches are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E273261C01
2.198,0.458 2.573,0.156 true 2.635,0.063 2.948,0.26 0.313,0.198 10 false *A
*A w/ DAB Function


Select "Panel&Steering Switch" from the "Function Check/Setting I" screen.


d.
E225786E01
2.269,1.407 3.085,1.407 false 0.344,1.149 1.04,1.149 false 2.888,1.063 3.085,1.063 false 0.148,1.048 0.304,1.200 0.156,0.152 10 *a 3.087,0.962 3.243,1.114 0.156,0.152 10 *b 3.087,1.327 3.243,1.480 0.156,0.152 10 *c

Panel&Steering Switch Check Mode

Screen Description
Display Content
*a: Switch condition "Pushed" is displayed when any switch is pushed
*b: Number of switches pushed
·

Number of switches pushed at once is displayed

·

If 3 or more switches are pushed at once, "More than 3" is displayed


*c: Rotary switch direction Direction of rotary switch is displayed

i.

Operate each switch and check that the switch conditions are correctly displayed.

NOTICE:

When the "SETUP" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.





CHECK TOUCH SWITCH


HINT:
·

The touch switches on the screen are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E273262C01
2.24,0.448 2.604,0.198 true 2.667,0.104 2.979,0.302 0.313,0.198 10 false *A
*A w/ DAB Function


Select "Touch Switch" from the "Function Check/Setting I" screen.


d.
E176521

Touch Switch Check

i.

Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

HINT:
·

A "+" mark is displayed where the display is touched.

·

The "+" mark remains on the display even after the finger is removed.






CHECK MICROPHONE&VOICE RECOGNITION


HINT:
·

The microphone and microphone input level are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E273263C01
2.177,0.479 2.542,0.188 true 2.615,0.094 2.927,0.292 0.313,0.198 10 false *A
*A w/ DAB Function


Select "Mic&Voice Recognition" from the "Function Check/Setting I" screen.


d.
E225853N02
3.164,0.784 3.32,0.941 0.156,0.157 10 *a 3.135,0.875 2.82,0.875 false

Microphone&Voice Recognition Check

Screen Description
Display Content
*a: Microphone input level meter Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.

i.

When speaking into the microphone, check that the microphone input level meter changes according to the input level.

HINT:

The microphone is active at all times when this screen is displayed.





CHECK COLOR BAR


HINT:
·

The display color on the screen is checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E273264C01
2.188,0.458 2.625,0.167 true 2.698,0.063 3.01,0.26 0.313,0.198 10 false *A
*A w/ DAB Function


Select "Color Bar" from the "Function Check/Setting I" screen.


d.
E226305

Color Bar Check Mode

i.

Select a color bar from the "Color Bar Check Mode" screen.


ii.

Check the display color.

HINT:
·

The entire screen turns to the color or stripe selected.

·

Touching the display will return to the "Color Bar Check Mode" screen.






CHECK VEHICLE SIGNAL


HINT:
·

Vehicle signals received by the radio and display receiver assembly are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E273265C01
2.208,0.458 2.625,0.156 true 2.677,0.073 2.99,0.271 0.313,0.198 10 false *A
*A w/ DAB Function


Select "Vehicle Signal" from the "Function Check/Setting I" screen.


d.
E225776

Vehicle Signal Check Mode

Screen Description
Display Content
Battery Battery voltage is displayed.
IG Ignition switch ON/OFF state is displayed.
PKB Parking brake ON/OFF state is displayed.
REV Reverse signal ON/OFF state is displayed.
SPEED Vehicle speed is displayed in km/h.
TAIL Tail signal (Light control switch) ON/OFF state is displayed.
ADIM/TCAN Brightness state DIM (with) / BRIGHT (without) is displayed.

HINT:
·

Only items sending vehicle signals will be displayed.

·

This screen displays vehicle signals input to the radio and display receiver assembly.

·

This screen is updated once per second when vehicle input signals change.



i.

When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.




CHECK HANDS-FREE VOICE QUALITY AND VOLUME SETTING


HINT:
·

The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E273266C01
2.167,0.448 2.5,0.146 true 2.573,0.063 2.885,0.26 0.313,0.198 10 false *A
*A w/ DAB Function


Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.


d.
E225788E03
0.117,0.653 0.272,0.807 0.155,0.154 10 *a 0.325,0.738 0.582,0.738 false 0.117,0.911 0.272,1.065 0.155,0.154 10 *b 0.325,0.996 0.582,0.996 false

Hands-Free Voice Quality Setting (Receive/Send Voice Level adjustment)

Screen Description
Display Content
*a: Receive voice level adjustment Setting for the voice level received from "Bluetooth" compatible phones.
*b: Send voice level adjustment Setting for the voice level sent from "Bluetooth" compatible phones.

NOTICE:

Sound quality may deteriorate when the receive voice or send voice level is changed more than necessary. For this reason, check that the received voice or sent voice quality is still acceptable after changing this setting.


i.

If the voice level is low, press the up button, and if the voice level is loud, press the down button.



e.
E228924C05
2.865,1.021 3.135,1.021 false 2.833,1.552 3.135,1.552 false 1.792,1.635 1.792,1.906 false 3.146,0.927 3.313,1.083 0.167,0.156 10 *a 3.156,1.479 3.323,1.635 0.167,0.156 10 *b 1.708,1.917 1.875,2.073 0.167,0.156 10 *c
*a Numeric keypad
*b Setting button
*c Reset button


Hands-Free Voice Quality Setting (Voice Quality Type adjustment)

i.

If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.


ii.

When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

Setting
Parameter Target Phenomenon Voice Quality Type (FUJITSU TEN) Voice Quality Type (Panasonic) Voice Quality Type (Pioneer) Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
Echo The other party hears a lot of echo when speaking to you. 1000
2000
0001 0001
0002
0003
0004
0005
The amount of echo the other party hears of their own voice is reduced. When both parties speak at the same time, your voice suddenly drops in volume, cuts out etc.
Half Duplex When both parties speak at the same time, your voice suddenly drops in volume, cuts out etc. 0100
0200
0002 0010
0020
0030
0040
0050
When both parties speak at the same time, the phenomenon by which the other party's voice suddenly drops in volume, cuts out etc. reduces. The amount of echo the other party hears of their own voice increases.
Noise The other party hears a lot of vehicle noise etc. when listening to your voice. 0010
0020
- 0100
0200
0300
0400
0500
The amount of vehicle noise etc. the other party hears when listening to your voice reduces. The quality of your voice, that the other party hears, reduces.
Voice Quality The quality of your voice, that the other party hears, is low. 0001
0002
0003 1000
2000
3000
4000
5000
The quality of your voice, that the other party hears, increases. The amount of noise etc. the other party hears when listening to your voice increases.

HINT:
·

Refer to the "Unit Version Information" screen to confirm radio and display receiver assembly manufacturer information.

·

The type of adjustments that can be made using voice quality type adjustment only adjust the sound quality of your voice that the other party hears. It cannot adjust the sound quality of the other party's voice that you hear.

·

The default value is "0000".

·

Settings will be applied when the normal screen is returned to.

·

When multiple setting values are available, the higher the setting value, the bigger the effect. However, as the positive effects increase, so do the negative effects.

·

If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.

·

If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.






CHECK DAB RECEPTION (w/ DAB Function)


HINT:
·

The reception condition of DAB (Digital Audio Broadcast) can be checked.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E274379

Select "Next Page" from the "Function Check/Setting I" screen.


d.
E235721

Select "DAB Reception Check" from the "Function Check/Setting II" screen.


e.
E235722E01
1.734,0.852 1.906,0.852 false 0.152,0.783 0.345,0.955 0.193,0.172 10 *a 0.355,0.873 0.548,0.873 false 2.701,1.17 3.027,1.17 false 2.696,1.324 3.023,1.324 false 1.939,0.774 2.132,0.946 0.193,0.172 10 *b 3.073,1.071 3.266,1.243 0.193,0.172 10 *c 3.073,1.247 3.266,1.419 0.193,0.172 10 *d

DAB Reception Check

*a: Channel Change Switch Description
Display Content
Up or down button Enables the channel to be changed to the one to be checked

*b: Check Switch Description
Display Condition Content
CHECK Before/after check Starts checking
STOP During check Stops checking

*c: Antenna Connection Check Result Description
Display Content
OK Connected properly
NG Not connected properly
- Not equipped with DAB antenna

*d: DAB Tuner Reception Level Check Result Description
Display Content
Black Good reception
Red Poor reception
- Not equipped with DAB antenna



CHECK UNIT VERSION INFORMATION


HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.



b.
E229432

Select "Service Information" from the "Service Menu" screen.


c.
E249762

Select "Version Information" from the "Service Information" screen.


d.
E230280

Press the "Push" switch.


e.
E228232N05
1.896,0.417 2.031,0.167 2.031,0.167 2.26,0.167 true 0.646,0.802 0.354,0.802 true 2.125,1.313 3.146,1.313 true 0.646,1.313 0.354,1.313 true 2.302,0.063 2.469,0.229 0.167,0.167 10 *a 0.135,0.698 0.302,0.865 0.167,0.167 10 *b 0.135,1.219 0.302,1.385 0.167,0.167 10 *c 3.177,1.229 3.344,1.396 0.167,0.167 10 *d

Unit Version Information

Screen Description
Display Content
*a: Device name Target device
*b: Manufacturer name Manufacturer of the ECU (target device)
*c: Component name Component name of the ECU (target device)
*d: Version Version of the ECU (target device)

HINT:

Depending on the manufacturer, some component names and versions will be displayed differently.




CHECK SOFTWARE ERROR HISTORY


HINT:

This function is used to check the cause when the radio and display receiver assembly screen is blacked out.


a.

Check software error history.

i.

Connect the GTS to the DLC3.


ii.

Engine start.


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.

Body Electrical > Navigation System > Utility
Tester Display
Software Error History
50005 212 4150

v.

When an item is stored for Software Error History, record it before repairing the radio and display receiver assembly.

Software Error History Screen Description
Error Description Trigger Detail
Software Reset Navi Microcomputer Hexadecimal Number
Audio Microcomputer
CAN Microcomputer
No Video Signal Front Monitor
Rear Monitor
MOST Cold Restart Always

HINT:
·

Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

·

If an error that is unsupported by the GTS occurs, a "-" is displayed for the display items.





b.

Clear software error history.

i.

When DTCs are cleared using any of the following operations, Software Error History will be cleared as well.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

·

Cleared using the GTS.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.





CHECK OPTICAL DISC ERROR HISTORY


HINT:

This function is used to check the cause of an optical disc error.


a.

Check optical disc error history.

i.

Connect the GTS to the DLC3.


ii.

Engine start.


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.

Body Electrical > Navigation System > Utility
Tester Display
Optical Disc Error History
50005 212 4151

v.

When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

Optical Disc Error History Screen Description
Display Content
Error Type Displays the type of error.
Device Displays the malfunctioning device.
Date Displays the date and time that the malfunction occurred.

"Error Type" Screen Description
Error Type Detection Condition Action
Read Error When a disc read error occurs. Proceed to next suspected area shown in Problem Symptoms Table
Click here(Click here)
Disc damaged/upside down/dirty When it is determined that any of the following is the cause of the disc read error:
·

The disc cannot be read.

·

The disc cannot be read because of dirt or scratches.

·

The disc cannot be read because it is inserted upside down.


Cannot determine disc type An unsuitable disc is inserted.
DPS error When an error occurs while decoding MP3/WMA files.
Some files are corrupt
·

When MP3/WMA files cannot be played back because they are unsupported.

·

Even though the file extensions are MP3 or WMA, files cannot be played back because the header information cannot be read.


Some files cannot be found
·

When a disc without music data is played back.

·

When there are no playable MP3/WMA files.


Copy protection violation When a file with copyright protection that cannot be played back is played back.

"Device" Screen Description
Device Component
DVD-P Not available
CD-P Radio and display receiver assembly
R-Seat DVD-P Not available

HINT:
·

Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.

·

If an error that is unsupported by the GTS occurs, a "-" or blank is displayed for the display items.





b.

Clear optical disc error history.

i.

When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

·

Cleared using the GTS.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.