Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE ASSEMBLY
RM3090E _52 Drivetrain _008752 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0049178 AUTOMATIC TRANSAXLE ASSEMBLY A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C201725

Engage the splines of the input shaft and turbine runner.


b.
C201726

Engage the splines of the stator shaft and the stator while turning the torque converter assembly.

HINT:

If the stator shaft splines are difficult to engage with the stator splines, move the torque converter assembly back approximately 10 mm and engage the splines while rotating the torque converter assembly.



c.
C201727

Turn the torque converter assembly to insert the key of the oil pump drive gear into the groove of the torque converter assembly.


d.

Clean the torque converter assembly set bolt holes.


e.
C281371C01
2.365,0.823 2.365,0.583 false 2.448,1.198 2.635,1.198 false 1.167,0.802 1.042,0.385 1.042,0.385 0.896,0.385 false 0.948,3 1.083,3 1.083,3 1.26,2.375 true 2.292,0.844 2.604,1 0.313,0.156 10 false *a 2.271,1.115 2.583,1.271 0.313,0.156 10 false *b 2.146,0.24 2.458,0.396 0.313,0.156 10 false A 0.729,0.292 1.042,0.448 0.313,0.156 10 false *a 0.781,2.917 1.094,3.073 0.313,0.156 10 false *b
*a Engine Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure dimension A between the transaxle contact surface of the engine*a and the torque converter assembly contact surface of the drive plate*b.

NOTICE:

Make sure to deduct the thickness of the straightedge.



f.
C207515N01
2.49,0.292 2.604,0.479 0.115,0.188 10 B

Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that dimension B is more than dimension A, which was measured in the previous step.

Standard:

A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transaxle assembly is installed to the engine with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 30500 2.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C201731C01
1.083,1.135 1.417,1.135 false 1.792,1.219 2.156,1.219 false 0.938,1.063 1.125,1.25 0.188,0.188 10 *2 2.198,1.146 2.375,1.313 0.177,0.167 10 *1
*1 Torque Converter Assembly Centerpiece
*2 Crankshaft


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1 g (0.0353 oz.)



b.
C239000N01
2.414,2.267 2.533,2.428 0.119,0.161 10 A 2.818,2.74 2.937,2.901 0.119,0.161 10 A 0.934,2.303 1.054,2.464 0.119,0.161 10 A 0.701,2.852 0.82,3.013 0.119,0.161 10 B 2.947,3.416 3.066,3.577 0.119,0.161 10 B 2.875,3.817 2.994,3.978 0.119,0.161 10 C 2.663,4.155 2.782,4.316 0.119,0.161 10 C 1.205,4.33 1.324,4.491 0.119,0.161 10 C 0.798,4.172 0.917,4.333 0.119,0.161 10 C

While keeping the engine and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the 9 bolts shown in the illustration.

Torque:
for Bolt A : 64 N*m (653 kgf*cm, 47 ft.*lbf)
for Bolt B : 46 N*m (469 kgf*cm, 34 ft.*lbf)
for Bolt C : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:
·

Confirm that the 2 knock pins are installed to the transaxle contact surface of the engine cylinder block before installing the automatic transaxle assembly.

·

Do not forcibly pry on the automatic transaxle assembly.

·

Check that the torque converter rotates smoothly after installation of the automatic transaxle assembly.



HINT:

Bolt length:

Bolt A: 55 mm (2.17 in.)

Bolt B: 50 mm (1.97 in.)

Bolt C: 33 mm (1.30 in.)



Hide 35150 3.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

a.

Apply ATF to a new O-ring and install it to the transmission case plug assembly.


b.

Install the transmission case plug assembly to the automatic transaxle assembly.


Hide 33823 4.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the automatic transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 12325A 5.INSTALL ENGINE MOUNTING BRACKET LH

a.

Clean the bolts and the installation holes in the engine mounting bracket LH.


b.

Apply adhesive to 2 or 3 threads on the ends of the 4 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the engine mounting bracket LH to the automatic transaxle assembly with the 4 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12321A 6.INSTALL REAR ENGINE MOUNTING BRACKET

a.

Install the rear engine mounting bracket to the automatic transaxle assembly with the 3 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 12311A 7.INSTALL FRONT ENGINE MOUNTING BRACKET

a.
C280480N01
1.625,1.365 1.781,1.563 0.156,0.198 10 false A 2.156,1.229 2.313,1.427 0.156,0.198 10 false B 1.135,1.521 1.292,1.719 0.156,0.198 10 false A 0.865,0.833 1.021,1.031 0.156,0.198 10 false A

Install the front engine mounting bracket to the automatic transaxle assembly with the 4 bolts.

Torque:
for Bolt A : 64 N*m (653 kgf*cm, 47 ft.*lbf)
for Bolt B : 13.5 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 33493A 8.INSTALL TRANSMISSION OIL COOLER

a.

Install the transmission oil cooler to the front engine mounting bracket with the 2 bolts.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


b.
C280479C01
1.99,1.875 2.156,1.552 2.156,1.552 2.417,1.552 true 1.708,1.563 1.573,1.323 1.573,1.323 1.323,1.323 true 2.458,1.448 2.771,1.604 0.313,0.156 10 *a 1.156,1.25 1.469,1.406 0.313,0.156 10 *b
*a Pink paint mark
*b White paint mark


Connect the oil cooler inlet hose and oil cooler outlet hose, and slide the clips to secure it.

NOTICE:
·

Make sure that the paint marks are inthe position shown in the illustration.

·

Make sure that the claws in the illustration are facing toward the front end of the vehicle.




Hide 82824 9.INSTALL WIRING HARNESS CONNECTOR

a.

Install the wiring harness connector to the automatic transaxle assembly.


b.
C238952N02
2.188,0.302 2.292,0.458 0.104,0.156 10 1 1.792,0.229 1.896,0.385 0.104,0.156 10 2

Install and tighten the 2 bolts in the order shown in the illustration.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)


Hide 10.INSTALL BREATHER HOSE BRACKET

a.

Install the breather hose bracket to the automatic transaxle assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Attach the transmission breather hose sub-assembly to the breather hose bracket.


Hide 11.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 2 wire harness clamp brackets to the automatic transaxle assembly with the 2 bolts.

Torque:
19.1 N*m (195 kgf*cm, 14 ft.*lbf)


Hide 12.CONNECT WIRE HARNESS

a.

Attach the 5 wire harness clamps and connect the park/neutral position switch connector.


b.

Connect the connector to the wiring harness connector and turn the lock lever and secure the connector with the lock lever.


c.

Connect the ground cable with the bolt.

Torque:
19.1 N*m (195 kgf*cm, 14 ft.*lbf)


Hide 14.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 15.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Remove any adhesive remaining in the 6 bolt holes of the torque converter assembly and 6 drive plate and torque converter setting assembly bolts.


b.

Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley with SST.

SST
09213-54015  09330-00021  91551-80650  

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

HINT:

First install the black-colored bolt, and then the remaining 5 silver-colored bolts.



d.

Install the flywheel housing under cover.


Hide 16.CHECK AUTOMATIC TRANSAXLE SYSTEM

NOTICE:

If automatic transmission parts have been replaced, refer to the Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION