Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › OIL PUMP
RM3090E _52 Drivetrain _008752 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0049181 OIL PUMP G

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL PUMP  INSPECTION  


PROCEDURE

Hide 1.INSPECT OIL PUMP ASSEMBLY

a.
C138512

Turn the drive gear with 2 screwdrivers and make sure that it rotates smoothly.

NOTICE:

Be careful not to damage the oil seal lip.



Hide 2.INSPECT CLEARANCE OF FRONT OIL PUMP BODY AND GEAR SUB-ASSEMBLY

a.

Inspect the body clearance.

i.
C138509

Push the driven gear to one side of the front oil pump body.


ii.

Using a feeler gauge, measure the front oil pump body clearance.

Standard clearance:

0.075 to 0.145 mm (0.00296 to 0.00570 in.)


Maximum clearance:

0.145 mm (0.00570 in.)


If the clearance is more than the maximum, replace the front oil pump drive gear, front oil pump driven gear or front oil pump body sub-assembly.



b.

Inspect the side clearance.

i.
C138511

Using a straightedge and feeler gauge, measure the side clearance of both gears.

Standard side clearance:

0.025 to 0.040 mm (0.000985 to 0.00157 in.)


Maximum side clearance:

0.040 mm (0.00157 in.)


If the clearance is more than the maximum, replace the front oil pump drive gear, front oil pump driven gear or front oil pump body sub-assembly.

HINT:

There are 5 different thicknesses for the front oil pump drive gear and front oil pump driven gear.

Drive Gear Thickness
Mark Thickness
1 11.547 to 11.555 mm (0.45461 to 0.45492 in.)
2 11.555 to 11.563 mm (0.45493 to 0.45523 in.)
3 11.564 to 11.571 mm (0.45528 to 0.45555 in.)
4 11.572 to 11.579 mm (0.45559 to 0.45586 in.)
5 11.580 to 11.587 mm (0.45591 to 0.45618 in.)

Driven Gear Thickness
Mark Thickness
1 11.547 to 11.555 mm (0.45461 to 0.45492 in.)
2 11.555 to 11.563 mm (0.45493 to 0.45523 in.)
3 11.564 to 11.571 mm (0.45528 to 0.45555 in.)
4 11.572 to 11.579 mm (0.45559 to 0.45586 in.)
5 11.580 to 11.587 mm (0.45591 to 0.45618 in.)




Hide 3.INSPECT FRONT OIL PUMP BODY SUB-ASSEMBLY

a.
C138514

Using a caliper gauge, measure the inside diameter of the front oil pump body bushing.

Standard inside diameter:

43.135 to 43.160 mm (1.6983 to 1.6992 in.)


Maximum inside diameter:

43.160 mm (1.6992 in.)


If the inside diameter is more than the maximum, replace the front oil pump body sub-assembly.


Hide 4.INSPECT STATOR SHAFT ASSEMBLY

a.
C138513

Using a caliper gauge, measure the inside diameter of the stator shaft bushing.

Standard inside diameter:

22.500 to 22.526 mm (0.88583 to 0.88684 in.)


Maximum inside diameter:

22.576 mm (0.88882 in.)


If the inside diameter is more than the maximum, replace the stator shaft assembly.