Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › VALVE BODY ASSEMBLY
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047085 VALVE BODY ASSEMBLY G

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  VALVE BODY ASSEMBLY  INSPECTION  


PROCEDURE

Hide 35240 1.INSPECT SHIFT SOLENOID VALVE SL

a.
C188295
0.158,0.099 0.355,0.264 0.197,0.164 10 *a
*a Component without harness connected
(Shift Solenoid Valve SL)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve SL connector terminal - Shift solenoid valve SL body 20°C (68°F) 11 to 15 Ω


If the value is not as specified, replace the shift solenoid valve SL.


b.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Shift solenoid valve SL connector Valve moves and makes an operating noise
Battery negative (-) → Shift solenoid valve SL body


If the operation cannot be done as specified, replace the shift solenoid valve SL.


Hide 35290 2.INSPECT SHIFT SOLENOID VALVE SLT

a.
C201747
0.493,0.48 0.674,0.675 0.18,0.195 10 1 2.533,0.48 2.713,0.675 0.18,0.195 10 2 1.163,4.15 1.372,4.356 0.209,0.206 10 (-) 1.919,4.15 2.147,4.35 0.228,0.2 10 (+) 1.509,0.804 0.652,0.57 false 1.785,0.789 2.479,0.549 false 0.493,2.733 0.674,2.928 0.18,0.195 10 1 2.533,2.733 2.713,2.928 0.18,0.195 10 2 1.509,3.056 0.652,2.823 false 1.785,3.042 2.479,2.802 false 0.135,0.025 0.357,0.231 0.222,0.206 10 *a
*a Component without harness connected
(Shift Solenoid Valve SLT, SLU, SL1, SL2, SL3, SL4)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω


If the value is not as specified, replace the shift solenoid valve SLT.


b.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
Battery positive (+) with a 21 W bulb → Terminal 1 Valve moves and makes an operating noise
Battery negative (-) → Terminal 2


If the operation cannot be done as specified, replace the shift solenoid valve SLT.


Hide 35280 3.INSPECT SHIFT SOLENOID VALVE SLU

HINT:

Refer to Inspect Shift Solenoid Valve SLT.


Hide 35210 4.INSPECT SHIFT SOLENOID VALVE SL1

HINT:

Refer to Inspect Shift Solenoid Valve SLT.


Hide 35220 5.INSPECT SHIFT SOLENOID VALVE SL2

HINT:

Refer to Inspect Shift Solenoid Valve SLT.


Hide 35210 6.INSPECT SHIFT SOLENOID VALVE SL3

HINT:

Refer to Inspect Shift Solenoid Valve SLT.


Hide 35220 7.INSPECT SHIFT SOLENOID VALVE SL4

HINT:

Refer to Inspect Shift Solenoid Valve SLT.