Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM3090E _58 Vehicle Interior _008789 HEATING / AIR CONDITIONING _0049188 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1413/13  Evaporator Temperature Sensor Circuit  


DESCRIPTION

The No. 1 cooler evaporator sub-assembly is installed on the evaporator in the air conditioner unit to detect the temperature of the air that has passed through the evaporator and is used to control the air conditioning. It sends signals to the air conditioning amplifier assembly. The resistance of the No. 1 cooler evaporator sub-assembly changes in accordance with the cooled air temperature that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler evaporator sub-assembly and reads voltage changes as the resistance of the No. 1 cooler evaporator sub-assembly changes. This sensor is used for frost prevention.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1413/13 Evaporator Temperature Sensor Circuit Open or short in No. 1 cooler evaporator sub-assembly circuit
·

No. 1 cooler evaporator sub-assembly

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly


Memorized (4 seconds or more) -

HINT:

The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E229251E33
2.021,1.417 2.365,1.677 0.344,0.26 10 1 2.021,0.458 2.115,0.635 0.094,0.177 10 2 4.771,0.458 4.865,0.635 0.094,0.177 10 6 4.771,1.417 5.135,1.698 0.365,0.281 10 5 4.969,0.552 5.677,0.844 0.708,0.292 10 TEA 2.688,1.906 4.24,2.26 1.552,0.354 10 Air Conditioning Harness Assembly 4.969,1.5 5.583,1.813 0.615,0.313 10 SGA 0.792,1.927 1.094,2.104 0.302,0.177 10 aa1 0.792,2.094 2.344,2.458 1.552,0.365 10 No. 1 Cooler Evaporator Sub-assembly 4.75,1.917 5.052,2.167 0.302,0.25 10 z7 4.729,2.083 6.302,2.417 1.573,0.333 10 Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Evaporator Fin Thermistor No. 1 cooler evaporator sub-assembly Min.: -29.70°C (-21.46°F)
Max.: 59.55°C (139.19°F)
Actual evaporator temperature displayed -
Body Electrical > Air Conditioner > Data List
Tester Display
Evaporator Fin Thermistor
50003 121 3
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.INSPECT NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
2.INSPECT NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
a.

Remove the No. 1 cooler evaporator sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT EVAPORATOR TEMPERATURE SENSOR>REMOVAL


b.

Inspect the No. 1 cooler evaporator sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT EVAPORATOR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK AIR CONDITIONING HARNESS ASSEMBLY

NG

REPLACE NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY (NO. 1 COOLER THERMISTOR)

3.CHECK AIR CONDITIONING HARNESS ASSEMBLY
a.
E269945C01
1.5,0.281 1.896,0.521 0.396,0.24 1.51,2.01 1.906,2.25 0.396,0.24 1.51,2 1.906,2.24 0.396,0.24 1.104,1.708 1.281,1.708 1.281,1.708 1.521,1.427 false 1.948,1.708 1.76,1.708 1.76,1.708 1.656,1.458 false 0.052,0.042 0.365,0.24 0.313,0.198 10 *a 1.625,0.323 1.938,0.521 0.313,0.198 10 z7 0.052,1.885 0.365,2.083 0.313,0.198 10 *b 1.99,1.635 2.302,1.833 0.313,0.198 10 TEA 0.74,1.625 1.052,1.823 0.313,0.198 10 SGA 1.594,2.042 1.948,2.219 0.354,0.177 10 aa1
*a Front view of air conditioning harness assembly
(to Air Conditioning Amplifier Assembly)
*b Front view of air conditioning harness assembly
(to No. 1 Cooler Evaporator Sub-assembly)


Disconnect the air conditioning harness assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z7-6 (TEA) - aa1-2 Always Below 1 Ω
z7-5 (SGA) - aa1-1 Always Below 1 Ω
z7-6 (TEA) - Body ground Always 10 kΩ or higher
z7-5 (SGA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE AIR CONDITIONING HARNESS ASSEMBLY