Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM3090E _58 Vehicle Interior _008789 HEATING / AIR CONDITIONING _0049188 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1443/43  Air Outlet Damper Control Servo Motor Circuit  


DESCRIPTION

The No. 1 air conditioning radiator damper servo sub-assembly (mode) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal, reverse) based on the signals to move the No. 1 air conditioning radiator damper servo sub-assembly (mode) to any position, which controls the air outlet switching.

The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1443/43 Air Outlet Damper Control Servo Motor Circuit Air outlet damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 air conditioning radiator damper servo sub-assembly (mode)
·

No. 1 air conditioning radiator damper servo sub-assembly (mode)

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly


Memorized (30 seconds or more) -

HINT:

The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E269946E03
5.573,3.115 6.031,3.313 0.458,0.198 10 false z7 3.531,3.302 5.094,3.719 1.563,0.417 10 false Air Conditioning Harness Assembly 5.563,3.302 6.604,3.927 1.042,0.625 10 false Air Conditioning Amplifier Assembly 0.115,3.125 2,3.604 1.885,0.479 10 false No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Mode) 5.625,0.833 6.083,1.031 0.458,0.198 10 false BUS G 5.385,0.729 5.573,0.927 0.188,0.198 10 false 2 5.635,2.521 6.094,2.719 0.458,0.198 10 false B BUS 5.385,1.563 5.573,1.76 0.188,0.198 10 false 3 5.625,1.698 6.083,1.896 0.458,0.198 10 false BUS 5.375,2.396 5.563,2.594 0.188,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

When the battery is disconnected or the air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>INITIALIZATION


HINT:

Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Operate the MODE switch.


e.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


f.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Air Outlet Servo Pulse (D) No. 1 air conditioning radiator damper servo sub-assembly (mode) target pulse Min.: 0
Max.: 255
FACE: 47 (pulse)
B/L: 37 (pulse)
FOOT: 17 (pulse)
FOOT/DEF: 9 (pulse)
DEF: 5 (pulse)
-
Body Electrical > Air Conditioner > Data List
Tester Display
Air Outlet Servo Pulse (D)
50003 121 72
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

2.CHECK NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (MODE)

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.CHECK NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (MODE)
a.

Replace the No. 1 air conditioning radiator damper servo sub-assembly (mode).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.



b.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121
OK:

DTC B1443/43 is not output.



Result:
Proceed to
OK
NG



OK

END (NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY [MODE] IS DEFECTIVE)

NG

3.CHECK AIR CONDITIONING HARNESS ASSEMBLY
3.CHECK AIR CONDITIONING HARNESS ASSEMBLY
a.

Replace the air conditioning harness assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>REMOVAL

HINT:

Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.



b.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121
OK:

DTC B1443/43 is not output.



Result:
Proceed to
OK
NG



OK

END (AIR CONDITIONING HARNESS ASSEMBLY IS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY