Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM3090E _58 Vehicle Interior _008789 HEATING / AIR CONDITIONING _0049188 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B14A3  Front Passenger Side Solar Sensor Short Circuit  


DESCRIPTION

E107008E21
0.667,0.115 2.344,0.365 1.677,0.25 10 Resistance of Photodiode 0.51,0.698 0.969,0.948 0.458,0.25 10 High 0.51,2.344 0.969,2.615 0.458,0.271 10 Low 0.927,2.594 1.635,2.948 0.708,0.354 10 Weak 2.323,2.583 3.219,3.031 0.896,0.448 10 Strong 1,2.938 3,3.365 2,0.427 10 Strength of Solar Radiation

The automatic light control sensor is installed on the upper side of the instrument panel. It detects sunlight to control air conditioning AUTO mode. The output voltage from the automatic light control sensor varies in accordance with the amount of sunlight. When the sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases. The air conditioning amplifier assembly detects changes in the output voltage from the automatic light control sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B14A3 Front Passenger Side Solar Sensor Short Circuit Short in front passenger side automatic light control sensor circuit
·

Automatic light control sensor

·

Harness or connector

·

Main body ECU (multiplex network body ECU)

·

Air conditioning amplifier assembly


Memorized (4 seconds or more) -

HINT:

The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E269950E02
4.646,1.719 4.958,1.917 0.313,0.198 10 G78 0.74,3.385 2.229,3.74 1.49,0.354 10 Automatic Light Control Sensor 4.656,1.896 6.885,2.281 2.229,0.385 10 Main Body ECU (Multiplex Network Body ECU) 0.74,3.208 1.052,3.406 0.313,0.198 10 G2 4.885,3.219 5.198,3.417 0.313,0.198 10 G81 4.885,3.385 6.542,3.75 1.656,0.365 10 Air Conditioning Amplifier Assembly 5.104,2.813 5.583,3.01 0.479,0.198 10 TSP 4.833,2.688 5.063,2.875 0.229,0.188 10 32 2.01,2.688 2.635,2.875 0.625,0.188 10 2*1, 1*2 1.073,2.802 1.979,3 0.906,0.198 10 TSR*1, TSL*2 5.104,1.302 5.583,1.5 0.479,0.198 10 CLTE 4.823,1.198 5.052,1.385 0.229,0.188 10 22 5.104,0.729 5.583,0.927 0.479,0.198 10 CLTB 4.823,0.615 5.052,0.802 0.229,0.188 10 20 1.552,0.719 1.938,0.917 0.385,0.198 10 CLTB 1.552,1.281 1.958,1.479 0.406,0.198 10 CLTE 2.031,0.615 2.26,0.802 0.229,0.188 10 6 2.021,1.177 2.25,1.365 0.229,0.188 10 3 0.167,4.417 1.073,4.615 0.906,0.198 10 *2: for RHD 0.177,4.125 1.083,4.323 0.906,0.198 10 *1: for LHD

CAUTION / NOTICE / HINT

NOTICE:
·

When the battery is disconnected or the air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>INITIALIZATION

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Solar Sensor (P Side) Front passenger side automatic light control sensor Min.: 0
Max.: 255
Front passenger side automatic light control sensor value increases as brightness increases -
Body Electrical > Air Conditioner > Data List
Tester Display
Solar Sensor (P Side)
50003 121 5
OK:

The display is as specified in the Normal Condition column.



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
E269949C01
1.51,0.354 1.906,0.625 0.396,0.271 0.979,1.604 1.156,1.604 1.156,1.604 1.542,1.448 true 2.333,1.833 2.146,1.833 2.146,1.833 1.865,1.635 true 0.042,0.052 0.354,0.25 0.313,0.198 10 *a 2.365,1.75 2.833,1.948 0.469,0.198 10 CLTB 0.583,1.531 1,1.729 0.417,0.198 10 CLTE 1.615,0.406 1.865,0.594 0.25,0.188 10 G2
*a Front view of wire harness connector
(to Automatic Light Control Sensor)


Disconnect the automatic light control sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G2-6 (CLTB) - G2-3 (CLTE) Ignition switch off Below 1 V
G2-6 (CLTB) - G2-3 (CLTE) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - AUTOMATIC LIGHT CONTROL SENSOR)
3.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the G81 air conditioning amplifier assembly connector.


b.

Disconnect the G2 automatic light control sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
G81-32 (TSP) - G2-2 (TSR) Always Below 1 Ω
G81-32 (TSP) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
G81-32 (TSP) - G2-1 (TSL) Always Below 1 Ω
G81-32 (TSP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR
a.

Remove the automatic light control sensor with the connectors still connected.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC LIGHT CONTROL SENSOR>REMOVAL


b.

Inspect the automatic light control sensor.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC LIGHT CONTROL SENSOR>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - AUTOMATIC LIGHT CONTROL SENSOR)
a.

Disconnect the G78 main body ECU (multiplex network body ECU) connector.


b.

Disconnect G2 automatic light control sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G78-20 (CLTB) - G2-6 (CLTB) Always Below 1 Ω
G78-22 (CLTE) - G2-3 (CLTE) Always Below 1 Ω
G78-20 (CLTB) - Body ground Always 10 kΩ or higher
G78-22 (CLTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR