Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM3090E _58 Vehicle Interior _008789 HEATING / AIR CONDITIONING _0049188 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B14B2  Lost Communication with Front Panel LIN  


DESCRIPTION

The air conditioning control assembly communicates with the air conditioning amplifier assembly through the LIN communication system.

If the LIN communication system malfunctions, the air conditioning amplifier assembly does not operate even if the air conditioning control assembly is operated.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B14B2 Lost Communication with Front Panel LIN Lost communication with the air conditioning control assembly.
·

Harness or connector

·

LIN communication system

·

Air conditioning control assembly

·

Air conditioning amplifier assembly


Memorized (10 seconds or more) -

HINT:

The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E226613E34
0.802,2.479 1.302,2.854 0.5,0.375 10 G20 0.802,2.635 2.292,3.156 1.49,0.521 10 Air Conditioning Control Assembly 0.927,3.188 2.552,3.354 1.625,0.167 10 : LIN Communication Line 5,2.49 5.406,2.833 0.406,0.344 10 G81 5,2.656 6.583,3.333 1.583,0.677 10 Air Conditioning Amplifier Assembly 1.625,0.854 1.938,1.01 0.313,0.156 10 LIN1 1.656,1.406 1.938,1.594 0.281,0.188 10 IG+ 1.583,1.927 1.927,2.104 0.344,0.177 10 GND 2.01,0.729 2.115,0.896 0.104,0.167 10 6 2.01,1.292 2.156,1.458 0.146,0.167 10 8 2.021,1.823 2.24,1.979 0.219,0.156 10 5 2.823,1.542 3.594,1.74 0.771,0.198 10 HTR-IG 3.917,1.385 4.896,1.729 0.979,0.344 10 from IG1 NO.1 Relay 4.99,0.719 5.188,0.875 0.198,0.156 10 37 5.26,0.875 5.635,1.052 0.375,0.177 10 LIN1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the battery is disconnected or the air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>INITIALIZATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BATTERY)
a.
E269951C02
1.521,0.25 1.927,0.51 0.406,0.26 2.563,1.646 2.354,1.646 2.354,1.646 1.969,1.469 true 0.042,0.052 0.354,0.25 0.313,0.198 10 *a 1.594,0.302 1.906,0.5 0.313,0.198 10 G20 2.625,1.583 2.99,1.771 0.365,0.188 10 IG+
*a Front view of wire harness connector
(to Air Conditioning Control Assembly)


Disconnect the air conditioning control assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G20-8 (IG+) - Body ground Ignition switch off Below 1 V
G20-8 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BODY GROUND)
a.
E269951C01
1.521,0.25 1.927,0.51 0.406,0.26 1.01,1.594 1.25,1.594 1.25,1.594 1.469,1.438 true 0.042,0.052 0.354,0.25 0.313,0.198 10 *a 1.594,0.302 1.906,0.5 0.313,0.198 10 G20 0.646,1.51 1.01,1.698 0.365,0.188 10 GND
*a Front view of wire harness connector
(to Air Conditioning Control Assembly)


Disconnect the air conditioning control assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G20-5 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - AIR CONDITIONING CONTROL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - AIR CONDITIONING CONTROL ASSEMBLY)
a.

Disconnect the G20 air conditioning control assembly connector.


b.

Disconnect the G81 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G20-6 (LIN1) - G81-37 (LIN1) Always Below 1 Ω
G20-6 (LIN1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK AIR CONDITIONING CONTROL ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AIR CONDITIONING CONTROL ASSEMBLY

b.

Check the air conditioning control assembly operates normally.

HINT:

Since the air conditioning control assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning control assembly with a new or known good one and check that the condition returns to normal.


OK:

Air conditioning control assembly operation returns to normal.



Result:
Result Proceed to
OK A
NG (When troubleshooting according to Problem Symptoms Table) B
NG (When troubleshooting according to the DTC) C



A

END (AIR CONDITIONING CONTROL ASSEMBLY IS DEFECTIVE)

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY