Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
RM3090E _59 Vehicle Exterior _008793 SLIDING ROOF / CONVERTIBLE _0049191 SLIDING ROOF SYSTEM U

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Sliding Roof or Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Sliding Roof > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Open Switch OPEN switch signal ON or OFF ON: OPEN switch pressed
OFF: OPEN switch not pressed
-
Close Switch CLOSE switch signal ON or OFF ON: CLOSE switch pressed
OFF: CLOSE switch not pressed
-
Up Switch UP switch signal ON or OFF ON: UP switch pressed
OFF: UP switch not pressed
-
Down Switch DOWN switch signal ON or OFF ON: DOWN switch pressed
OFF: DOWN switch not pressed
-
Rear SW Auto Operation Sliding roof auto function ON or OFF Customization status displayed This item is not applicable to this vehicle
Front SW Auto Operation Sliding roof auto function ON or OFF Customization status displayed -
Hall IC1 Pulse Hall IC1 pulse output Lo or Hi Lo and Hi repeat during motor operation Lo: Hall IC1 output is low
Hi: Hall IC1 output is high
Hall IC1 Status Status of Hall IC1 Normal or Error Normal: Hall IC1 normal
Error: Hall IC1 not normal
-
Hall IC2 Pulse Hall IC2 pulse output Lo or Hi Lo and Hi repeat during motor operation Lo: Hall IC2 output is low
Hi: Hall IC2 output is high
Hall IC2 Status Status of Hall IC2 Normal or Error Normal: Hall IC2 normal
Error: Hall IC2 not normal
-
Ignition (Direct Signal) Ignition switch signal ON or OFF ON: Ignition switch ON
OFF: Ignition switch off
-
Ignition (MPX) Ignition switch signal (LIN signal) ON or OFF ON: Ignition switch ON
OFF: Ignition switch off
-
Door Courtesy Driver door courtesy light switch signal ON or OFF ON: Driver door open
OFF: Driver door closed
-
Door Handle Lock Button Entry lock switch ON or OFF ON: Entry lock switch is pressed
OFF: Entry lock switch is not pressed
This item is not applicable to this vehicle
Door Key Close Operation Key-linked sliding roof close signal ON or OFF ON: Door LOCK is turned to close position using key
OFF: Door LOCK is not turned
This item is not applicable to this vehicle
Door Key Open Operation Key-linked sliding roof open signal ON or OFF ON: Door UNLOCK is turned to open position using key
OFF: Door UNLOCK is not turned
This item is not applicable to this vehicle
Wireless Close Operation Wireless sliding roof close signal ON or OFF ON: Transmitter LOCK switch pressed
OFF: Transmitter LOCK switch not pressed
This item is not applicable to this vehicle
Wireless Open Operation Wireless sliding roof open signal ON or OFF ON: Transmitter UNLOCK switch pressed
OFF: Transmitter UNLOCK switch not pressed
This item is not applicable to this vehicle
Key Off Permission Key-off sliding roof operation permit signal ON or OFF ON: Front doors are not opened within 43 seconds after ignition switch turned off
OFF: Any status except "ON" status
-
Window Lock Window lock operation signal ON or OFF ON: Window lock switch is turned to lock
OFF: Window lock switch is turned to unlock
This item is not applicable to this vehicle
Door Key Related Operation Key-linked sliding roof open function operating direction Slide or Tilt Customization status displayed This item is not applicable to this vehicle
Wireless Key Rel Operation Wireless transmitter-linked sliding roof open function operating direction Slide or Tilt Customization status displayed This item is not applicable to this vehicle
Open Switch Failure(Past) Open switch failure signal (Past) ON or OFF ON: Sliding roof open switch failure signal (Past)
OFF: No sliding roof open switch failure signal (Past)
-
Close Switch Failure(Past) Close switch failure signal (Past) ON or OFF ON: Sliding roof close switch failure signal (Past)
OFF: No sliding roof close switch failure signal (Past)
-
Up Switch Failure(Past) Up switch failure signal (Past) ON or OFF ON: Sliding roof tilt up switch failure signal (Past)
OFF: No sliding roof tilt up switch failure signal (Past)
-
Down Switch Failure(Past) Down switch failure signal (Past) ON or OFF ON: Sliding roof tilt down switch failure signal (Past)
OFF: No sliding roof tilt down switch failure signal (Past)
-
Open Switch Failure(Current) Open switch failure signal (Current) ON or OFF ON: Sliding roof open switch failure signal (Current)
OFF: No sliding roof open switch failure signal (Current)
-
Close Switch Failure(Current) Close switch failure signal (Current) ON or OFF ON: Sliding roof close switch failure signal (Current)
OFF: No sliding roof close switch failure signal (Current)
-
Up Switch Failure(Current) Up switch failure signal (Current) ON or OFF ON: Sliding roof tilt up switch failure signal (Current)
OFF: No sliding roof tilt up switch failure signal (Current)
-
Down Switch Failure(Current) Down switch failure signal (Current) ON or OFF ON: Sliding roof tilt down switch failure signal (Current)
OFF: No sliding roof tilt down switch failure signal (Current)
-
Number of Trouble Codes Number of DTCs Min.: 0, Max.: 255 Number of stored DTCs -
Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Slide Roof Open Warning Sliding roof open warning ON or OFF Customization status displayed -


PERFORM ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Sliding Roof / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Sliding Roof > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Slide Roof Operate sliding roof motor OFF / Opn/Dwn / Clos/Up -