Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P244B  Diesel Particulate Filter Differential Pressure Too High  


DESCRIPTION

Refer to DTC P244A (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P244A).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P244B Diesel Particulate Filter Differential Pressure Too High While driving, Catalyst Differential Pressure becomes more than 0.37 for 3 seconds.
(1 trip detection logic)
·

DPF catalytic converter (Exhaust manifold converter sub-assembly)

·

Differential pressure sensor assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored

Related Data List
DTC No. Data List
P244B
·

DPF Differential Pressure

·

Catalyst Differential Press

·

Exhaust Fuel Addition FB



MONITOR DESCRIPTION

The ECM compares pressure upstream and downstream of the DPF catalyst to monitor the differential pressure. If the differential pressure is large, the ECM determines that the DPF catalyst is contaminated or has deteriorated and illuminates the MIL.

A244057E05
2.125,3.344 2.344,3.344 false 2.344,3.344 2.688,2.063 false 4,1.177 4.521,0.448 false 4.521,0.448 4.698,0.448 false 5.844,2.354 5.302,1.99 false 5.844,2.354 5.979,2.354 false 1.229,3.271 2.125,3.625 0.896,0.354 10 Stores P244B 3.531,2.906 3.99,3.135 0.458,0.229 10 MAF 0.135,0.094 2.292,0.323 2.156,0.229 10 Differential Pressure Malfunction: 0.25,1.427 1.24,1.896 0.99,0.469 10 DPF Differential Pressure 4.771,0.375 5.969,0.604 1.198,0.229 10 Clogged with PM 5.76,1.031 7.146,1.458 1.385,0.427 10 Increases PM amount of DPF catalyst 6.042,2.271 6.969,2.646 0.927,0.375 10 No PM in DPF catalyst 1.125,0.729 1.51,0.958 0.385,0.229 10 High 5.604,2.896 5.99,3.125 0.385,0.229 10 High 1.125,2.563 1.51,2.792 0.385,0.229 10 Low 1.573,2.906 1.958,3.135 0.385,0.229 10 Low

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P244B Engine is running at 4000 rpm with no load for 10 seconds or more.

CAUTION / NOTICE / HINT

NOTICE:
·
·

After replacing the fuel supply pump assembly, the ECM needs initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Record the stored DTC and freeze frame data.


e.

Check Exhaust Fuel Addition FB and Catalyst Differential Press in the freeze frame data.

HINT:
·

When the Exhaust Fuel Addition FB value is 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM forced regeneration.

·

When the Catalyst Differential Press value is 0.37 or more, it indicates a high possibility that DPF catalyst is clogged.




Result:
Proceed to
NEXT



NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244B)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244B)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Result Proceed to
DTC P244B is output A
DTC P244B is output at the same time as P2463*
Other relevant DTCs are output B


HINT:

*: When P244B is output at the same time as P2463, perform this diagnostic procedure. When DTC P244B is not output at the same time as P2463 is output, perform the diagnostic procedure for P244C (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P244A).




A

3.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)

B

9.GO TO DTC CHART
3.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.

Powertrain > Engine > Data List
Tester Display
DPF Differential Pressure
50003 61 238

d.

Check the DPF Differential Pressure values from idle speed to unloaded maximum engine speed.

Result:
Result Proceed to
DPF Differential Pressure increases as engine speed increases from idle speed A
Except above B


A241154E04
3.313,3.375 3.542,3.375 3.542,3.375 3.719,3.875 false 4.25,4.281 4.125,4.281 false 4.125,4.281 3.854,3.979 false 4.146,4.927 4.042,4.927 4.042,4.927 3.833,4.76 false 0.469,1.479 1.74,1.865 1.271,0.385 10 Engine Speed (rpm) 0.833,2.99 1.74,3.375 0.906,0.385 10 MAF (gm/sec) 0.688,4.115 1.698,4.521 1.01,0.406 10 DPF Differential Pressure (kPa) 4.198,4.854 4.323,5 0.125,0.146 10 A 1.771,1.875 1.875,2.156 0.104,0.281 10 0 1.781,3.24 1.885,3.521 0.104,0.281 10 0 1.792,4.615 1.896,4.896 0.104,0.281 10 0 0.677,0.854 1.948,1.24 1.271,0.385 10 Unloaded Maximum Engine Speed 2.385,3.281 3.344,3.521 0.958,0.24 10 Normal Piping 4.313,4.208 5.271,4.448 0.958,0.24 10 Clogged Piping 2.313,5.417 5.333,5.698 3.021,0.281 10 Negative pressure occurs for approx. 1 second.

HINT:

If DPF Differential Pressure indicates negative pressure for approx. 1 second as shown in the illustration (A) when the engine speed increases, the differential pressure sensor piping of the DPF catalyst may be clogged.




A

5.CHECK FOR BLACK SMOKE

B

4.CLEAN OR REPLACE VACUUM TRANSMITTING HOSE
4.CLEAN OR REPLACE VACUUM TRANSMITTING HOSE
a.

Even though it has been determined that the vacuum transmitting hose needs to be repaired or cleaned, make sure to perform all diagnostic procedures for DTC P244B before repairing or cleaning it.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR BLACK SMOKE
5.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the above procedure [A] 10 times [B].


e.

Check for black smoke emission during procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESS)

NG

8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
6.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESS)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst Differential Press.

Powertrain > Engine > Data List
Tester Display
Catalyst Differential Press
50003 61 608

d.

Check the value of Catalyst Differential Press at 4000 rpm without load.

Result:
Result Proceed to
Catalyst Differential Press is more than 0.37 A
Except above B




A

8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

B

7.PERFORM PM FORCED REGENERATION
7.PERFORM PM FORCED REGENERATION
a.

Clear the DTC and Exhaust Fuel Addition FB value by disconnecting the cable from the negative (-) battery terminal or removing the EFI-MAIN NO. 1 fuse for 1 minute or more.

HINT:
·

The accumulated PM volume stored in the ECM cannot be initialized using the GTS.

·

To perform PM forced regeneration, it is necessary to perform initialization of the accumulated PM volume stored in the ECM.




b.

Connect the GTS to the DLC3.


c.

Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.


d.

Move the shift lever to neutral and set the parking brake.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the DPF Rejuvenate (PM) / Data List / PM Accumulation Ratio.

Powertrain > Engine > Active Test
Active Test Display
Activate the DPF Rejuvenate (PM)
Data List Display
PM Accumulation Ratio
50004 61 97 725

g.

Perform the Active Test while the vehicle is driven at a constant vehicle speed within 50 to 100 km/h (31 to 62 mph) (transmission in 3rd gear) for more than 15 minutes.

HINT:
·

While the "Activate the DPF Rejuvenate (PM)" Active Test is being performed, the accelerator opening angle should be kept as constant as possible.

·

When you start driving, "DPNR/DPF Status Reju (PM)" on the Data List displays "Compl". However, continue to drive the vehicle until "PM Accumulation Ratio" drops to 0%.

·

Once "PM Accumulation Ratio" drops to 0%, regeneration is complete.




h.

Continue to drive the vehicle until "PM Accumulation Ratio" drops to 0%.

CAUTION:

Be aware of excessive heat on and around the exhaust pipes during PM forced regeneration.


NOTICE:

If PM forced regeneration stops, repair the malfunction that caused it to stop, and perform it again to complete the operation.


HINT:
·

PM forced regeneration completes in 15 to 40 minutes.

·

PM forced regeneration time changes depending on PM Accumulation Ratio and driving conditions.

·

A fail-safe stops PM forced regeneration if Catalyst Differential Press increases too much during regeneration

·

Exhaust Temperature B1S2 becomes 500°C (932°F) or higher within 20 minutes of PM forced regeneration start.

·

PM forced regeneration will be stopped if the accelerator pedal is depressed during regeneration. In this case, PM forced regeneration needs to be performed again.

·

Even if PM forced regeneration stops while it is occurring, the GTS displays Compl (complete) for DPNR/DPF Status Reju (PM).



Result:

PM forced regeneration completes normally.



Result:
Proceed to
OK
NG



OK

END

NG

10.CHECK FUEL INJECTION SYSTEM
8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

Even though it has been determined that the DPF catalytic converter (Exhaust manifold converter sub-assembly) needs to be replaced, make sure to perform all diagnostic procedures for DTC P244B before replacing it.


Result:
Proceed to
NEXT



NEXT

10.CHECK FUEL INJECTION SYSTEM
9.GO TO DTC CHART

Result:
Proceed to
NEXT



NEXT

10.CHECK FUEL INJECTION SYSTEM
10.CHECK FUEL INJECTION SYSTEM

Result:
Proceed to
NEXT



NEXT

11.CHECK INTAKE / EXHAUST SYSTEM
11.CHECK INTAKE / EXHAUST SYSTEM

Result:
Proceed to
NEXT



NEXT

12.CHECK AFTER TREATMENT CONTROL SYSTEM
12.CHECK AFTER TREATMENT CONTROL SYSTEM

Result:
Proceed to
NEXT



NEXT

13.REPAIR OR REPLACE MALFUNCTIONING PARTS
13.REPAIR OR REPLACE MALFUNCTIONING PARTS
HINT:

Repair, replace or clean the following items only when it has been determined necessary based on diagnosis for DTC P244B.


a.

Clean and/or repair the hoses of the differential pressure sensor.


b.

Replace the DPF catalytic converter (Exhaust manifold converter sub-assembly).

Click hereEngine / Hybrid System>2AD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(for DPF)>REMOVAL

NOTICE:

Perform Initialization procedure for DPF catalyst record clear.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTC and Exhaust Fuel Addition FB value by disconnecting the cable from the negative (-) battery terminal or removing the EFI-MAIN NO. 1 fuse for 1 minute or more.

HINT:
·

The accumulated PM volume stored in the ECM cannot be initialized using the GTS.

·

To perform PM forced regeneration, it is necessary to perform initialization of the accumulated PM volume stored in the ECM.




b.

Connect the GTS to the DLC3.


c.

Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.


d.

Move the shift lever to neutral and set the parking brake.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the DPF Rejuvenate (PM) / Data List / PM Accumulation Ratio.

Powertrain > Engine > Active Test
Active Test Display
Activate the DPF Rejuvenate (PM)
Data List Display
PM Accumulation Ratio
50004 61 97 725

g.

Perform the Active Test while the vehicle is driven at a constant vehicle speed within 50 to 100 km/h (31 to 62 mph) (transmission in 3rd gear) for more than 15 minutes.

HINT:
·

While the "Activate the DPF Rejuvenate (PM)" Active Test is being performed, the accelerator opening angle should be kept as constant as possible.

·

When you start driving, "DPNR/DPF Status Reju (PM)" on the Data List displays "Compl". However, continue to drive the vehicle until "PM Accumulation Ratio" drops to 0%.

·

Once "PM Accumulation Ratio" drops to 0%, regeneration is complete.




h.

Continue to drive the vehicle until "PM Accumulation Ratio" drops to 0%.

CAUTION:

Be aware of excessive heat on and around the exhaust pipes during PM forced regeneration.


NOTICE:

If PM forced regeneration stops, repair the malfunction that caused it to stop, and perform it again to complete the operation.


HINT:
·

PM forced regeneration completes in 15 to 40 minutes.

·

PM forced regeneration time changes depending on PM Accumulation Ratio and driving conditions.

·

A fail-safe stops PM forced regeneration if Catalyst Differential Press increases too much during regeneration

·

Exhaust Temperature B1S2 becomes 500°C (932°F) or higher within 20 minutes of PM forced regeneration start.

·

PM forced regeneration will be stopped if the accelerator pedal is depressed during regeneration. In this case, PM forced regeneration needs to be performed again.

·

Even if PM forced regeneration stops while it is occurring, the GTS displays Compl (complete) for DPNR/DPF Status Reju (PM).




Result:
Proceed to
NEXT



NEXT

END