Home › Power Source / Network › 1AD-FTV BATTERY / CHARGING › CHARGING SYSTEM › 2012.12–2015.10
RM3090E _57 Power Source / Network _008779 1AD-FTV BATTERY / CHARGING _0049276 CHARGING SYSTEM C

1AD-FTV BATTERY / CHARGING  CHARGING SYSTEM  P1550  Battery Current Sensor Circuit  P1551  Battery Current Sensor Circuit Low  P1552  Battery Current Sensor Circuit High  


DESCRIPTION

The battery current sensor built into the generator control ECU assembly detects the amount of charge/discharge current. The generator control ECU assembly sends voltage generation instructions to the generator assembly based on this signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1550 Battery Current Sensor Circuit Difference between the maximum and minimum current values of the battery current sensor is less than 1 A for 10 seconds or more with the ignition switch ON
(1 trip detection logic)
·

Generator control ECU assembly

·

Wire harness or connector


Does not come on DTC stored
P1551 Battery Current Sensor Circuit Low Battery current sensor output value is abnormally low for 30 seconds or more with the ignition switch ON
(1 trip detection logic)
·

Generator control ECU assembly

·

Wire harness or connector


Does not come on DTC stored
P1552 Battery Current Sensor Circuit High Battery current sensor output value is abnormally high for 30 seconds or more with the ignition switch ON
(1 trip detection logic)
·

Generator control ECU assembly

·

Wire harness or connector


Does not come on DTC stored

PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1550, P1551 OR P1552)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Charging Control / Trouble Codes.


e.

Read the DTCs.

Body Electrical > Charging Control > Trouble Codes
50001 222
Result:
Proceed to
DTC P1550, P1551 or P1552 is output
DTC P1550, P1551 or P1552 and other DTCs are output


HINT:

If any DTCs other than P1550, P1551 or P1552 are output, troubleshoot those DTCs first.




DTC P1550, P1551 or P1552 is output

2.READ VALUE USING GTS (BATTERY CURRENT)

DTC P1550, P1551 or P1552 and other DTCs are output

2.READ VALUE USING GTS (BATTERY CURRENT)
a.

Turn all of the electrical systems (headlights, blower motor, rear defogger, etc.) off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Charging Control / Data List / Battery Current.

Body Electrical > Charging Control > Data List
Tester Display
Battery Current
50003 222 4
Result:
Result Proceed to
Battery current is fixed at 0 A, or fluctuates by +/- 1 A or less between -100 and 100 A A
Battery current fluctuates between -20 and 0 A B




A

3.CHECK HARNESS AND CONNECTOR (GENERATOR CONTROL ECU ASSEMBLY (BATTERY CURRENT SENSOR) - GENERATOR ASSEMBLY)

B

3.CHECK HARNESS AND CONNECTOR (GENERATOR CONTROL ECU ASSEMBLY (BATTERY CURRENT SENSOR) - GENERATOR ASSEMBLY)
a.

Disconnect the A58 generator control ECU assembly connector.


b.

Disconnect the B62 generator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A58-6 (LIN1) - B62-1 (LIN) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A58-6 (LIN1) or B62-1 (LIN) - Body ground Ignition switch off
(while LIN communication is stopped)
10 kΩ or higher



Result:
Result
OK
NG



OK

REPLACE GENERATOR CONTROL ECU ASSEMBLY (BATTERY CURRENT SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR