Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0049280 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the IG1 circuit, IG2 circuit or IG hold circuit in the certification ECU (smart key ECU assembly) is detected.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2271 Ignition Hold Monitor Malfunction
When either of the following conditions is met (1-trip detection logic*):
·

The IG1 or IG2 circuit in the certification ECU (smart key ECU assembly) is malfunctioning.

·

The IG hold circuit in the certification ECU (smart key ECU assembly) is malfunctioning.


·

AM2 fuse

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


IG ON

*: Only detected while a malfunction is present and the engine switch is on (IG)

HINT:
·

The IG1 and IG2 circuits activate the IG1 and IG2 relays.

·

After the IG1 and IG2 circuits turn on, even if the CPU operates incorrectly, the IG hold circuit maintains the power source mode in on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The engine switch cannot be turned on (IG) (the engine cannot be started). The power source mode cannot be changed to on (IG).


HINT:

Related Data List and Active Test Items

DTC Data List Item Active Test Item
B2271
Power Source Control:
·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Inside)

·

Latch Circuit


Starting Control:
·

Ignition


-


WIRING DIAGRAM

C278822E01
0.26,1.104 1.281,1.292 1.021,0.188 10 from Battery 1.594,1.323 2.021,1.51 0.427,0.188 10 AM2 2.375,1.146 2.802,1.333 0.427,0.188 10 G82 2.385,4.083 2.813,4.271 0.427,0.188 10 G82 2.385,7.188 2.813,7.375 0.427,0.188 10 G82 2.417,7 2.844,7.188 0.427,0.188 10 11 2.458,3.896 2.885,4.083 0.427,0.188 10 9 2.729,4.073 3.156,4.26 0.427,0.188 10 IG2D 2.729,7.188 3.156,7.375 0.427,0.188 10 E 1.01,4.406 1.438,4.594 0.427,0.188 10 IG2 1.469,3.552 1.896,3.74 0.427,0.188 10 5 1.469,3.99 1.896,4.177 0.427,0.188 10 1 0.708,3.563 1.135,3.75 0.427,0.188 10 3 0.708,3.969 1.135,4.156 0.427,0.188 10 2 3.115,2.969 3.542,3.156 0.427,0.188 10 IG1D 2.729,1.146 3.156,1.333 0.427,0.188 10 +B 2.49,0.927 2.917,1.115 0.427,0.188 10 2 3.594,2.958 4.021,3.146 0.427,0.188 10 G84 3.688,2.771 4.115,2.958 0.427,0.188 10 6 4.208,2.552 4.635,2.74 0.427,0.188 10 3A 4.219,2.958 4.646,3.146 0.427,0.188 10 3C 4.208,2.771 4.635,2.958 0.427,0.188 10 43 4.24,2.354 4.667,2.542 0.427,0.188 10 1 6.052,2.719 6.594,3.156 0.542,0.438 10 ECU-IG NO. 1 6.552,2.552 6.979,2.74 0.427,0.188 10 3C 6.563,3.729 6.99,3.917 0.427,0.188 10 3C 6.552,4.917 6.979,5.104 0.427,0.188 10 3C 6.573,5.323 7,5.51 0.427,0.188 10 3D 6.042,3.948 6.646,4.125 0.604,0.177 10 WIP FR 6.021,5.063 6.563,5.427 0.542,0.365 10 S-HTR RH 6.604,5.135 7.031,5.323 0.427,0.188 10 9 6.625,4.708 7.052,4.896 0.427,0.188 10 3 6.604,3.542 7.031,3.729 0.427,0.188 10 1 6.573,2.365 7,2.552 0.427,0.188 10 27 5.042,5.677 5.771,5.865 0.729,0.188 10 IG1 NO. 3 5.052,4.479 5.781,4.667 0.729,0.188 10 IG1 NO. 2 5.031,3.292 5.76,3.479 0.729,0.188 10 IG1 NO. 1 1.854,8.26 4.688,8.521 2.833,0.26 10 Certification ECU (Smart Key ECU Assembly) 4.125,6.042 6.854,6.25 2.729,0.208 10 Instrument Panel Junction Block Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Start Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
B268625C36
0.427,1.219 0.865,1.458 0.438,0.24 0.896,1.771 1.271,1.344 true 0.115,0.063 0.302,0.219 0.188,0.156 10 *a 0.521,1.24 0.948,1.406 0.427,0.167 10 G82 0.688,1.813 1.073,1.958 0.385,0.146 10 +B
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G82-2 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)
a.
B268625C38
0.521,1.323 0.958,1.563 0.438,0.24 2.063,1.583 2.448,1.792 true 0.115,0.063 0.302,0.219 0.188,0.156 10 false *a 2.521,1.74 2.906,1.885 0.385,0.146 10 false E 0.583,1.375 1.031,1.563 0.448,0.188 10 false G82
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-11 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the G82 certification ECU (smart key ECU assembly) connector.

B264896C38
1.979,0.854 2.5,1.104 0.521,0.25 4.615,0.865 5.135,1.115 0.521,0.25 2,1.74 2.167,2.354 false 4.354,1.635 4.135,2.302 false 0.542,0.271 0.854,0.469 0.313,0.198 10 *a 2.083,0.896 2.521,1.073 0.438,0.177 10 G82 4.75,0.927 5.188,1.104 0.438,0.177 10 G84 3.969,2.354 4.406,2.531 0.438,0.177 10 IG1D 2.031,2.396 2.469,2.573 0.438,0.177 10 IG2D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G82-9 (IG2D) - Body ground Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher
G84-6 (IG1D) - Body ground



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)