Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0049280 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit that goes from the ACC output terminal of the certification ECU (smart key ECU assembly) to the ACC relay.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2274 ACC Monitor Malfunction Malfunction in the ACC relay circuit in the certification ECU (smart key ECU assembly) or in the external circuit (1-trip detection logic*).
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

AM2 fuse

·

ACC relay (instrument panel junction block assembly)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Wait 10 seconds after turning the engine switch on (ACC) or on (IG), and then wait another 10 seconds after turning the engine switch off.

*: Only detected while a malfunction is present.

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction due to the relay being stuck on, the ACC relay does not turn off even though the engine switch is off.

·

If there is a malfunction due to the relay being stuck off, the ACC relay does not turn on even though the engine switch is on (ACC).

HINT:

The engine switch can be turned on (IG) and the engine can be started.



-

Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2274
Power Source Control:
·

ACC Relay Monitor


Starting Control:
·

Ignition


-

WIRING DIAGRAM

B269101E05
0.156,1.073 1.125,1.271 0.969,0.198 10 from Battery 1.615,1.25 2.073,1.448 0.458,0.198 10 AM2 2.385,1.104 2.792,1.26 0.406,0.156 10 G82 2.396,2.25 2.854,2.448 0.458,0.198 10 G82 3.542,1.75 3.885,1.896 0.344,0.146 10 G84 4.271,1.344 4.729,1.542 0.458,0.198 10 3D 4.271,1.75 4.729,1.948 0.458,0.198 10 3C 6.417,1.344 6.875,1.542 0.458,0.198 10 3A 6.406,1.76 6.865,1.958 0.458,0.198 10 3D 4.729,1.5 5.188,1.698 0.458,0.198 10 ACC 2.74,1.104 3.198,1.302 0.458,0.198 10 +B 2.729,2.271 3.188,2.469 0.458,0.198 10 E 3.083,1.75 3.542,1.948 0.458,0.198 10 ACCD 2.448,2.042 2.677,2.229 0.229,0.188 10 11 2.458,0.896 2.688,1.083 0.229,0.188 10 2 3.625,1.531 3.854,1.719 0.229,0.188 10 4 4.281,1.125 4.667,1.302 0.385,0.177 10 51 4.292,1.563 4.521,1.75 0.229,0.188 10 45 6.438,1.125 6.667,1.313 0.229,0.188 10 1 6.448,1.542 6.677,1.729 0.229,0.188 10 9 5.438,2.083 5.896,2.281 0.458,0.198 10 ACC 4.188,2.458 6.906,2.635 2.719,0.177 10 Instrument Panel Junction Block Assembly 2.302,2.917 4.208,3.313 1.906,0.396 10 Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Start Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
B268625C36
0.427,1.219 0.865,1.458 0.438,0.24 0.896,1.771 1.271,1.344 true 0.115,0.063 0.302,0.219 0.188,0.156 10 *a 0.521,1.24 0.948,1.406 0.427,0.167 10 G82 0.688,1.813 1.073,1.958 0.385,0.146 10 +B
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G82-2 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)
a.
B268625C38
0.521,1.323 0.958,1.563 0.438,0.24 2.063,1.583 2.448,1.792 true 0.115,0.063 0.302,0.219 0.188,0.156 10 false *a 2.521,1.74 2.906,1.885 0.385,0.146 10 false E 0.583,1.375 1.031,1.563 0.448,0.188 10 false G82
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-11 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G84 connector from the certification ECU (smart key ECU assembly).


b.

Disconnect the 3C and 3D connectors from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-4 (ACCD) - 3C-45 Always Below 1 Ω
3D-9 - Body ground
G84-4 (ACCD) or 3C-45 - Body ground 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.

Remove the instrument panel junction block assembly.

C278638C01
3.365,2.229 3.854,2.5 0.49,0.271 1.531,0.385 2.021,0.656 0.49,0.271 4.542,0.406 5.031,0.677 0.49,0.271 0.365,0.198 0.677,0.354 0.313,0.156 10 false *a 1.698,0.438 2.021,0.604 0.323,0.167 10 false 3C 4.708,0.469 5.031,0.635 0.323,0.167 10 false 3D 3.5,2.292 3.823,2.458 0.323,0.167 10 false 3A
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-1 - 3D-51 Battery voltage not applied to terminals 3C-45 and 3D-9 10 kΩ or higher
Battery voltage applied to terminals 3C-45 and 3D-9 Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B268626C07
1.333,0.188 1.792,0.469 0.458,0.281 1.125,1.01 0.813,0.51 false 1.417,0.25 2.031,0.448 0.615,0.198 10 G84 0.406,0.406 1.021,0.604 0.615,0.198 10 ACCD 0.094,0.052 0.708,0.25 0.615,0.198 10 *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the G84 certification ECU (smart key ECU assembly) connector


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G84-4 (ACCD) - Body ground Engine switch off → Engine switch on (ACC) 1 V or less → 8.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)