Home › Engine / Hybrid System › 2AD-FHV EMISSION CONTROL › EGR VALVE
RM3090E _51 Engine / Hybrid System _008736 2AD-FHV EMISSION CONTROL _0049291 EGR VALVE G

2AD-FHV EMISSION CONTROL  EGR VALVE  INSPECTION  


PROCEDURE

Hide 25800 1.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.
A201817
0.927,1.813 0.927,1.146 true 2.5,1.823 2.5,1.156 true 0.885,0.979 1.052,1.177 0.167,0.198 10 5 1.281,0.979 1.417,1.177 0.135,0.198 10 4 2.063,0.979 2.219,1.198 0.156,0.219 10 2 2.458,0.979 2.615,1.188 0.156,0.208 10 1 1.677,0.979 1.865,1.167 0.188,0.188 10 3 0.823,1.823 1.167,2.042 0.344,0.219 10 M+ 2.417,1.833 2.75,2.031 0.333,0.198 10 M- 0.052,0.052 0.365,0.208 0.313,0.156 10 *a
*a Component without harness connected
(Electric EGR Control Valve Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (M-) - 5 (M+) 25°C (77°F) 0.3 to 100 Ω


HINT:

The temperature indicated under "Condition" is the temperature of the electric EGR control valve assembly.


If the result is not as specified, replace the electric EGR control valve assembly.


Hide 25800 2.VISUAL CHECK ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.

Visually check the electric EGR control valve assembly for deposits.

If there are deposits, clean the electric EGR control valve assembly.

NOTICE:
·

When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.

·

Do not forcibly open the valve as it may be damaged or deformed.

·

When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto this part or soaking the part in solvent may damage the part.




b.
A201816
0.531,3.073 0.667,2.5 0.667,2.5 0.833,2.5 true 2.708,3 2.844,2.427 2.844,2.427 3.01,2.427 true 2.385,3.854 2.167,4.313 2.167,4.313 2,4.313 true 3.052,2.333 3.365,2.49 0.313,0.156 10 *1 0.802,4.135 1.115,4.292 0.313,0.156 10 *a 2.49,4.156 2.802,4.313 0.313,0.156 10 *b 0.885,2.406 1.042,2.604 0.156,0.198 10 A 1.823,4.219 2.135,4.375 0.313,0.156 10 *1
*1 Gap
*a CORRECT
*b INCORRECT


Hold the electric EGR control valve assembly up to a light, and then from the side indicated by the arrow in the illustration, visually check that there is no gap between the valve and body.

OK:

No light passes through (there is no gap between the valve and body).


If light passes through (there is a gap between the valve and body), replace the electric EGR control valve assembly.

HINT:

Light passes through part A shown in the illustration even if the valve is completely closed. This is not a problem.