Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2012.12–2014.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0048745 NAVIGATION SYSTEM(for HDD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  Sound Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the navigation ECU sub-assembly via this circuit.

The sound signal that has been sent is amplified by the navigation ECU sub-assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the navigation ECU sub-assembly or speakers.

WIRING DIAGRAM

E229861E37
0.813,0.813 1.24,0.969 0.427,0.156 10 AUXO 0.896,1.281 1.323,1.438 0.427,0.156 10 ARO 0.938,1.75 1.365,1.906 0.427,0.156 10 ALO 0.813,2.229 1.24,2.385 0.427,0.156 10 ASGN 0.813,2.708 1.24,2.865 0.427,0.156 10 AGND 2.552,2.844 3.323,3.083 0.771,0.24 10 Shielded 4.063,2.865 4.719,3.021 0.656,0.156 10 Shielded 5.927,0.729 6.354,0.885 0.427,0.156 10 ADPG 5.927,1.219 6.354,1.375 0.427,0.156 10 VAR+ 5.688,0.677 5.865,0.833 0.177,0.156 10 25 5.698,1.167 5.875,1.323 0.177,0.156 10 26 5.698,1.625 5.875,1.781 0.177,0.156 10 28 5.698,2.115 5.875,2.271 0.177,0.156 10 27 5.698,2.583 5.875,2.74 0.177,0.156 10 11 1.323,0.688 1.5,0.844 0.177,0.156 10 8 1.323,1.146 1.5,1.302 0.177,0.156 10 5 1.323,1.615 1.5,1.771 0.177,0.156 10 6 1.323,2.083 1.5,2.24 0.177,0.156 10 7 1.323,2.594 1.5,2.75 0.177,0.156 10 9 0.438,3.219 0.792,3.375 0.354,0.156 10 G145 0.417,3.385 1.604,3.781 1.188,0.396 10 No. 1 Stereo Jack Adapter Assembly 5.802,3.354 6.813,3.667 1.01,0.313 10 Navigation ECU Sub-assembly 5.927,1.667 6.354,1.823 0.427,0.156 10 VAL+ 5.927,2.177 6.354,2.333 0.427,0.156 10 VA- 5.927,2.635 6.354,2.792 0.427,0.156 10 AGND 5.802,3.177 6.313,3.365 0.51,0.188 10 G139

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the G139 navigation ECU sub-assembly connector.


b.

Disconnect the G145 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G139-25 (ADPG) - G145-8 (AUXO) Always Below 1 Ω
G139-26 (VAR+) - G145-5 (ARO) Always Below 1 Ω
G139-28 (VAL+) - G145-6 (ALO) Always Below 1 Ω
G139-27 (VA-) - G145-7 (ASGN) Always Below 1 Ω
G139-11 (AGND) - G145-9 (AGND) Always Below 1 Ω
G139-25 (ADPG) - Body ground Always 10 kΩ or higher
G139-26 (VAR+) - Body ground Always 10 kΩ or higher
G139-28 (VAL+) - Body ground Always 10 kΩ or higher
G139-27 (VA-) - Body ground Always 10 kΩ or higher
G139-11 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR