Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2012.12–2014.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0048745 NAVIGATION SYSTEM(for HDD) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The navigation ECU sub-assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Telephone microphone signal is lost.
·

Map light assembly (telephone microphone assembly)

·

Navigation ECU sub-assembly

·

Harness or connector



WIRING DIAGRAM

E270419E01
2.646,0.771 2.865,0.927 0.219,0.156 10 12 2.635,1.406 2.854,1.563 0.219,0.156 10 9 2.156,0.771 2.583,0.969 0.427,0.198 10 SNS2 2.177,1.427 2.615,1.615 0.438,0.188 10 MCO- 0.917,2.042 1.354,2.229 0.438,0.188 10 Q7 0.896,2.229 2.344,2.458 1.448,0.229 10 Map Light Assembly 4.938,2.042 5.375,2.229 0.438,0.188 10 G139 1.125,0.781 1.854,1.333 0.729,0.552 10 Telephone Microphone Assembly 4.792,1.417 5.01,1.573 0.219,0.156 10 19 4.823,0.76 5.042,0.917 0.219,0.156 10 6 5.021,0.865 5.448,1.063 0.427,0.198 10 SNS2 5.01,1.531 5.448,1.719 0.438,0.188 10 MIN- 4.948,2.198 6.844,2.417 1.896,0.219 10 Navigation ECU Sub-assembly

PROCEDURE

1.CHECK NAVIGATION ECU SUB-ASSEMBLY
a.
E238726C01
1.458,0.031 1.979,0.354 0.521,0.323 2.083,1.25 2.292,1.781 2.292,1.781 2.385,1.781 true 0.063,0.031 0.219,0.198 0.156,0.167 10 *a 1.51,0.104 1.875,0.25 0.365,0.146 10 G139 2.448,1.708 2.792,1.844 0.344,0.135 10 MIN-
*a Component with harness connected
(Navigation ECU Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G139-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - MAP LIGHT ASSEMBLY [TELEPHONE MICROPHONE ASSEMBLY])

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - MAP LIGHT ASSEMBLY [TELEPHONE MICROPHONE ASSEMBLY])
a.

Disconnect the G139 navigation ECU sub-assembly connector.


b.

Disconnect the Q7 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G139-6 (SNS2) - Q7-12 (SNS2) Always Below 1 Ω
G139-19 (MIN-) - Q7-9 (MCO-) Always Below 1 Ω
G139-6 (SNS2) - Body ground Always 10 kΩ or higher
G139-19 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


b.
E244514E03
1.792,1.552 2.042,1.885 2.042,1.885 2.177,1.885 true 1.354,1.552 1.063,1.844 1.063,1.844 0.938,1.844 true 0.552,1.771 1.167,1.969 0.615,0.198 10 SNS2 2.271,1.792 2.885,1.99 0.615,0.198 10 MCO-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (SNS2) - 9 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

4.CHECK TELEPHONE MICROPHONE ASSEMBLY
4.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or normally functioning one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for HDD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for HDD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Proceed to
No DTCs are output
DTCs are output



No DTCs are output

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

DTCs are output

5.CHECK MAP LIGHT ASSEMBLY
5.CHECK MAP LIGHT ASSEMBLY
a.

Replace the map light assembly with a new or normally functioning one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for HDD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for HDD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Proceed to
No DTCs are output
DTCs are output



No DTCs are output

END (MAP LIGHT ASSEMBLY IS DEFECTIVE)

DTCs are output