Use the following procedure to troubleshoot the navigation system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points in problem analysis:
| What | Vehicle model, system name |
| When | Date, time, occurrence frequency |
| Where | Road conditions |
| Under what conditions? | Driving conditions, weather conditions |
| How did it happen? | Problem symptoms |
| Proceed to |
|---|
| NEXT |
NEXT
Measure the battery voltage.
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.
Condensation is not likely being produced and the temperature is not high or extremely low.
A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.
The navigation system may not operate normally when the temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Refer to Check System Normal Condition.
| Proceed to |
|---|
| Symptom is not normal operation |
| Symptom is normal operation |
Symptom is not normal operation
Symptom is normal operation
Check for DTC output.
for LHD:
for RHD:
| Proceed to |
|---|
| CAN DTCs are not output |
| CAN DTCs are output |
CAN DTCs are not output
CAN DTCs are output
for LHD:
for RHD:
Refer to DTC Check/Clear.
| Proceed to |
|---|
| DTCs are output |
| DTCs are not output |
DTCs are output
DTCs are not output
Refer to DTC Check/Clear.
The present DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.
| Proceed to |
|---|
| NEXT |
NEXT
Refer to DTC Check/Clear.
Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.
If more information is needed, perform a recheck using the "System Check Mode" screen after rechecking for DTCs using the GTS.
Check the DTCs and inspect the area that the code indicates.
| Proceed to |
|---|
| DTCs are output |
| DTCs are not output |
DTCs are output
DTCs are not output
Find the output code in Diagnostic Trouble Code Chart.
| Proceed to |
|---|
| NEXT |
NEXT
Enter the "HDD Check" screen. Refer to Check Hard Disc in Operation Check.
"OK" is displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Refer to Problem Symptoms Table.
If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| Fault is not listed in Problem Symptoms Table |
| Fault is listed in Problem Symptoms Table |
Fault is not listed in Problem Symptoms Table
Fault is listed in Problem Symptoms Table
Refer to Terminals of ECU.
| Proceed to |
|---|
| NEXT |
NEXT
Adjust, repair or replace as necessary.
| Proceed to |
|---|
| NEXT |
NEXT
After clearing DTCs, recheck for DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT