Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1380  Stop Light Control Relay Malfunction  


DESCRIPTION

Upon receiving the hill-start assist control operating signal from the skid control ECU (brake actuator assembly), the relay contact turns on and the stop light comes on.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1380 Stop Light Control Relay Malfunction Either condition is met:
1.

When the voltage at the IG1 terminal is between 10 and 14 V and the stop light control relay drive output (STPO) is on, a signal has not been input to the STP terminal for 2 seconds or more.

2.

When the voltage at the IG1 terminal is between 10 and 14 V and the stop light control relay drive output (STPO) is off, the signal at the STP is different from the input signal at the STP2 for 5 seconds or more.


·

ECU-IG NO.3 fuse

·

STOP fuse

·

Stop light switch circuit

·

Stop light control relay (STOP LP)

·

Stop light control relay circuit

·

Skid control ECU (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC C1425 is output together with DTC C1380, inspect and repair the trouble areas indicated by DTC C1425 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off


Result:
Result
OK
NG




OK

2.CHECK TERMINAL VOLTAGE (STP TERMINAL)

NG

2.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Turn the ignition switch off.


c.

Disconnect the A64 skid control ECU (brake actuator assembly) connector.


d.
C199357C51
1.635,0.083 2.01,0.344 0.375,0.26 0.51,0.438 1.25,0.844 false 1.698,0.125 2.156,0.323 0.458,0.198 10 false A64 0.198,0.354 0.656,0.552 0.458,0.198 10 false STP 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A64-2 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Result:
Result
OK
NG




OK

3.CHECK TERMINAL VOLTAGE (STP2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

3.CHECK TERMINAL VOLTAGE (STP2 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness in the locking part and connecting part of the connector.


c.

Disconnect the A64 skid control ECU (brake actuator assembly) connector.


d.
C199357C56
1.635,0.083 2.01,0.344 0.375,0.26 2.198,1.25 2.448,1.854 false 1.698,0.125 2.156,0.323 0.458,0.198 10 false A64 2.417,1.917 2.875,2.115 0.458,0.198 10 false STP2 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A64-22 (STP2) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Result:
Result
OK
NG




OK

4.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)

4.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Reconnect the A64 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (STOP LP) Relay ON/OFF Stop lights come on
Vehicle condition: Vehicle stopped
f.

While performing the Active Test, check the illumination condition of the stop lights and "Stop Light Relay Output" in the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light control relay (STOP LP) output ON or OFF OFF: Relay output off (Stop lights off)
ON: Relay output on (Stop lights on)
-
Chassis > ABS/VSC/TRC > Active Test
Active Test Display
Stop Light Relay
Data List Display
Stop Light Relay Output
50004 105 5 291
Result:
Result Proceed to
When Active Test performed, Data List item changes between ON and OFF and stop lights turn on and off A
When Active Test performed, Data List item changes between ON and OFF, but stop lights do not turn on B



A

5.RECONFIRM DTC

B

6.INSPECT STOP LIGHT CONTROL RELAY (STOP LP)
5.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Start the engine.


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC C1380 is not output
DTC C1380 is output




DTC C1380 is not output

DTC C1380 is output

6.INSPECT STOP LIGHT CONTROL RELAY (STOP LP)
a.

Remove the stop light control relay (STOP LP) from the No. 2 engine room relay block assembly.


b.
A087121C01
2.354,0.604 2.354,0.292 false 2.49,1.115 2.958,1.115 false 2.49,1.615 2.958,1.615 false 2.042,0.604 1.865,0.292 false 2.635,0.604 2.813,0.292 false 0.313,1.396 0.51,1.604 0.198,0.208 10 1 1.813,0.083 2.01,0.292 0.198,0.208 10 1 1.313,1.396 1.51,1.604 0.198,0.208 10 2 2.76,0.083 2.958,0.292 0.198,0.208 10 2 0.313,0.844 0.51,1.052 0.198,0.208 10 3 3.01,1.531 3.208,1.74 0.198,0.208 10 3 0.938,0.365 1.135,0.573 0.198,0.208 10 4 2.302,0.083 2.5,0.292 0.198,0.208 10 4 1.313,0.844 1.51,1.052 0.198,0.208 10 5 3.01,1.021 3.208,1.229 0.198,0.208 10 5 0.125,0.094 0.354,0.323 0.229,0.229 10 *1
*1 Stop Light Control Relay (STOP LP)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery positive voltage is applied to terminal 1 and battery negative voltage is applied to terminal 2 10 kΩ or higher
Battery positive voltage is not applied to terminal 1 and battery negative voltage is not applied to terminal 2 Below 1 Ω
3 - 5 Battery positive voltage is applied to terminal 1 and battery negative voltage is applied to terminal 2 Below 1 Ω
Battery positive voltage is not applied to terminal 1 and battery negative voltage is not applied to terminal 2 10 kΩ or higher


Result:
Result
OK
NG




OK

7.CHECK TERMINAL VOLTAGE (STOP LIGHT POWER SOURCE TERMINAL)

NG

REPLACE STOP LAMP CONTROL RELAY (STOP LP)

7.CHECK TERMINAL VOLTAGE (STOP LIGHT POWER SOURCE TERMINAL)
a.
C279052C01
0,0 0.313,0.156 0.313,0.156 10 *a
*a Component without Stop Light Control Relay (STOP LP)
(No. 2 Engine Room Relay Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 - Body ground Always 11 to 14 V
2 - Body ground Ignition switch ON 11 to 14 V


Result:
Result
OK
NG




OK

8.CHECK TERMINAL VOLTAGE (STPO TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK TERMINAL VOLTAGE (STPO TERMINAL)
a.

Install the stop light control relay (STOP LP).


b.

Make sure that there is no looseness in the locking part and connecting part of the connector.


c.

Disconnect the A64 skid control ECU (brake actuator assembly) connector.


d.

Turn the ignition switch to ON.


e.
C199357C52
1.615,0.073 1.979,0.302 0.365,0.229 2.354,1.823 1.99,1.396 false 1.688,0.104 2.021,0.302 0.333,0.198 10 false A64 2.219,1.865 2.615,2.063 0.396,0.198 10 false STPO 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A64-31 (STPO) - Body ground Ignition switch ON 11 to 14 V


Result:
Result
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STPO CIRCUIT)