Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  AUTO LSD Indicator Light Remains ON  


DESCRIPTION

The AUTO LSD is a system for 2WD vehicles. When the VSC OFF switch (traction control switch) is pushed on, the AUTO LSD function is available and the AUTO LSD indicator light illuminates.

HINT:

The AUTO LSD does not operate even if the VSC OFF switch (traction control switch) is pressed under the following conditions:

·

The TRC/TRAC or VSC system is faulty.

·

The temperature inside the brake actuator assembly increases and the AUTO LSD operation is suspended.



WIRING DIAGRAM

C279159E07
3.385,2.573 3.844,2.771 0.458,0.198 10 false G51 3.385,2.75 5.073,3.115 1.688,0.365 10 false VSC OFF Switch (Traction Control Switch) 3.406,2.354 3.615,2.583 0.208,0.229 10 false E 4.031,2.344 4.219,2.573 0.188,0.229 10 false + 3.24,2.167 3.427,2.417 0.188,0.25 10 false 3 4.198,2.167 4.396,2.406 0.198,0.24 10 false 6 5.406,2.167 5.719,2.365 0.313,0.198 10 false 30 5.656,2.26 6.115,2.458 0.458,0.198 10 false CSW 5.51,2.823 5.969,3.021 0.458,0.198 10 false A64 5.51,3 7.115,3.531 1.604,0.531 10 false Skid Control ECU (Brake Actuator Assembly) 1.75,0.573 2.323,0.833 0.573,0.26 10 false CAN I/F 0.906,1.042 1.365,1.24 0.458,0.198 10 false CPU 1.063,2.948 1.813,3.229 0.75,0.281 10 false AUTO LSD 1.771,3.438 2.052,3.698 0.281,0.26 10 false IG 0.594,3.958 2.521,4.281 1.927,0.323 10 false Combination Meter Assembly 0.979,4.406 2.625,4.698 1.646,0.292 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

2.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output (for LHD)
DTC is output (for RHD)



DTC is not output

3.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)

DTC is output (for LHD)

DTC is output (for RHD)

3.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the A64 skid control ECU (brake actuator assembly) connector.


c.
C243286C10
1.531,0.115 1.969,0.385 0.438,0.271 1.792,1.385 1.719,1.854 false 0.042,0.021 0.24,0.188 0.198,0.167 10 *a 1.646,0.177 1.927,0.323 0.281,0.146 10 A64 1.51,1.885 1.885,2.031 0.375,0.146 10 CSW
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A64-30 (CSW) - Body ground VSC OFF switch held on Below 1 Ω
A64-30 (CSW) - Body ground VSC OFF switch off (Not pressed) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (AUTO LSD INDICATOR LIGHT)

NG

5.INSPECT TRACTION CONTROL SWITCH
4.READ VALUE USING GTS (AUTO LSD INDICATOR LIGHT)
a.

Reconnect the A64 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto LSD Indicator Light AUTO LSD indicator light ON or OFF OFF: AUTO LSD indicator light off
ON: AUTO LSD indicator light on
for 2WD
Chassis > ABS/VSC/TRC > Data List
Tester Display
Auto LSD Indicator Light
50003 105 334
g.

Check the GTS display condition of the AUTO LSD indicator light.


Result:
Proceed to
Display of the Data List remains OFF
Display of the Data List remains ON



Display of the Data List remains OFF

Display of the Data List remains ON

5.INSPECT TRACTION CONTROL SWITCH
a.

Remove the VSC OFF switch (traction control switch).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>REMOVAL


b.

Inspect the VSC OFF switch (traction control switch).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TRACTION CONTROL SWITCH)

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TRACTION CONTROL SWITCH)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-30 (CSW) - G51-6 (+) Always Below 1 Ω
G51-3 (E) - Body ground Always Below 1 Ω
A64-30 (CSW) or G51-6 (+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR