Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER
RM3090E _53 Suspension _008765 REAR SUSPENSION _0049359 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48517A 1.TEMPORARILY INSTALL REAR SHOCK ABSORBER BRACKET LH

a.
C278706C01
2.219,0.99 2.635,0.573 false 2.635,0.573 2.958,0.573 false 3.042,0.5 3.292,0.719 0.25,0.219 11 *1
*1 Protector


Temporarily install the bracket to the shock absorber with the bolt and nut.

NOTICE:

The absorber should be assembled with the protector positioned facing the front side of vehicle.


HINT:

The bolts can be installed in either direction, however, make sure that they are both installed in the same direction.



Hide 48540 2.TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY LH

a.

Support the rear No. 2 suspension arm assembly LH with a jack using a wooden block to avoid damage.


b.
C127561

Temporarily install the shock absorber upper side to the suspension member with the bolt and nut.

HINT:

The bolts can be installed in either direction, however, make sure that they are both installed in the same direction.



c.
C229148

Install the rear No. 1 shock absorber bracket to the rear axle carrier with the 2 bolts.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


Hide 3.STABILIZE SUSPENSION

a.
C284571C01
2.073,1.708 2.385,2.115 2.385,2.115 2.792,2.115 false 1.021,2.063 1.323,2.063 1.323,2.063 1.521,1.938 false 2.865,2.052 3.177,2.208 0.313,0.156 10 false *a 0.844,1.969 1.156,2.125 0.313,0.156 10 false *b 0.094,1.875 0.552,2.073 0.458,0.198 10 false (A)
*a Wooden Block
*b Jack
V100155

Jack Point


Jack up the rear No. 2 suspension arm assembly, placing a wooden block underneath to avoid damage. Apply load to the suspension so that the rear No. 2 suspension arm assembly is positioned as shown in the illustration.

Standard Length (A):

4.4 mm (0.1732 in.)


NOTICE:

Do not jack up the rear No. 2 suspension arm assembly too high as the vehicle may fall.


HINT:
·

If the rear No. 2 suspension arm assembly cannot be positioned as shown in the illustration even when the rear No. 2 suspension arm assembly is jacked up, apply additional load by placing a weight in the luggage compartment.

·

Use the same procedure for the RH and LH sides.




Hide 48540 4.TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH

a.

Tighten the bolt on the rear shock absorber (upper side).

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)

NOTICE:

Since a stopper nut is used, tighten the bolt.



b.

Tighten the bolt on the rear shock absorber (lower side).

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)

NOTICE:

Since a stopper nut is used, tighten the bolt.



Hide 5.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 6.INSPECT AND ADJUST REAR WHEEL ALIGNMENT