Home › Engine / Hybrid System › 2AR-FE STARTING › STARTER(for 1.7 kW Type)
RM3090E _51 Engine / Hybrid System _008402 2AR-FE STARTING _0049375 STARTER(for 1.7 kW Type) G

2AR-FE STARTING  STARTER(for 1.7 kW Type)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. Otherwise, the cable may become hot and cause injury.


NOTICE:

These tests must be performed within 3 to 5 seconds to avoid burning out the coil.


a.

Mount the starter assembly in a vise between aluminum plates.

NOTICE:

Ensure that the starter assembly is secured firmly in the vise to prevent it from falling out.



b.

Perform a pull-in test.

i.
A133511

Remove the nut and disconnect the lead wire from terminal C.


ii.
A133512
1.906,1.01 2.208,0.677 2.208,0.677 2.448,0.677 true 1.01,1.969 1.292,1.969 1.292,1.969 1.729,1.063 true 0.333,1.708 0.542,1.708 0.542,1.708 0.823,1.354 true 0.833,1.896 1.146,2.052 0.313,0.156 10 *1 2.51,0.594 2.823,0.75 0.313,0.156 10 *2 0.156,1.646 0.469,1.802 0.313,0.156 10 *3
*1 Terminal 50
*2 Terminal C
*3 Body
V100135

Moves Outward


Connect the battery to the starter assembly as shown in the illustration. Check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move outward, replace the motor terminal starter kit.



c.

Perform a holding test.

i.
A133513
1.917,1.021 2.208,0.76 2.208,0.76 2.417,0.76 true 0.5,1.354 0.792,1.354 true 1.052,1.906 1.333,1.906 1.333,1.906 1.677,1.052 true 0.885,1.833 1.198,1.99 0.313,0.156 10 *1 2.479,0.688 2.792,0.844 0.313,0.156 10 *2 0.323,1.292 0.635,1.448 0.313,0.156 10 *3
*1 Terminal 50
*2 Terminal C
*3 Body
V100135

Disconnect


Disconnect the negative (-) terminal lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains out.

If the clutch pinion gear moves inward, replace the motor terminal starter kit.



d.
A302255
0.375,1.75 0.594,1.75 0.594,1.75 0.844,1.292 true 1.063,1.906 1.24,1.906 1.24,1.906 1.708,1.073 true 1.885,1.021 2.104,0.823 2.104,0.823 2.354,0.823 true 0.885,1.844 1.198,2 0.313,0.156 10 false *1 2.385,0.76 2.698,0.917 0.313,0.156 10 false *2 0.208,1.688 0.521,1.844 0.313,0.156 10 false *3
*1 Terminal 50
*2 Terminal C
*3 Body
V100135

Disconnect
V100136

Returns Inward


Inspect the clutch pinion gear return.

i.

Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not move inward, replace the motor terminal starter kit.



e.

Perform an operation test without load.

i.

Connect the lead wire to terminal C with the nut. Make sure that the lead is not grounded.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.
A133510
1.354,1.146 1.583,1.146 1.583,1.146 1.854,1.708 true 0.99,2.854 1.24,2.854 1.24,2.854 1.698,1.948 true 0.823,2.781 1.135,2.938 0.313,0.156 10 *1 1.167,1.073 1.479,1.229 0.313,0.156 10 *2
*1 Terminal 50
*2 Terminal 30


Connect the battery and an ammeter (AC/DC 400A probe) to the starter assembly as shown in the illustration.

NOTICE:

Do not allow any leads to get caught as the pinion gear operates.



iii.

Check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.

Standard current:

90 A or less at 11.5 V


If the result is not as specified, replace the starter assembly.



Hide 28226A 2.INSPECT MOTOR TERMINAL STARTER KIT

A295769

a.

Check the plunger.

i.

Push in the plunger and check that it returns quickly to its original position.

If necessary, replace the motor terminal starter kit.



b.
A296173
2.135,1.427 2.667,0.844 2.667,0.844 2.854,0.844 false 1.25,1.927 1.5,1.927 1.5,1.927 1.729,1.594 true 1.052,1.865 1.365,2.021 0.313,0.156 10 *1 2.917,0.771 3.229,0.927 0.313,0.156 10 *2
*1 Terminal 50
*2 Terminal C


Inspect the resistance of the pull-in coil.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the motor terminal starter kit.



c.

Inspect the resistance of the holding coil.

i.
A296174
1.5,0.49 1.406,0.135 1.406,0.135 1.24,0.135 false 1.302,1.906 1.531,1.906 1.531,1.906 1.813,1.583 true 1.135,1.823 1.448,1.979 0.313,0.156 10 *1 1.052,0.063 1.365,0.219 0.313,0.156 10 *2
*1 Terminal 50
*2 Switch Body


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Switch body Always Below 2 Ω


If the result is not as specified, replace the motor terminal starter kit.



Hide 28160 3.INSPECT STARTER ARMATURE ASSEMBLY

HINT:

If there is no continuity between any segments, replace the starter armature assembly.


a.

Check the commutator for contamination and burns on its surface.

If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.


b.

Check if the commutator has an open circuit.

i.
A296175
0.719,1.51 0.969,1.51 0.969,1.51 1.344,1.292 true 1.438,1.188 2.25,1.927 2.25,1.927 2.49,1.927 true 0.563,1.438 0.875,1.594 0.313,0.156 10 *1 2.531,1.844 2.844,2 0.313,0.156 10 *1
*1 Segment


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



c.

Check if the commutator is grounded.

i.
A296176
0.698,1.635 0.938,1.635 0.938,1.635 1.354,1.219 true 1.948,1.042 2.25,0.458 2.25,0.458 2.521,0.458 true 0.531,1.573 0.844,1.729 0.313,0.156 10 *1 2.594,0.375 2.906,0.531 0.313,0.156 10 *2
*1 Segment
*2 Coil Core


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Coil core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



d.
A295766
2.854,0.948 3.167,1.104 0.313,0.156 10 *1
*1 Length


Using a vernier caliper, measure the commutator length.

Standard length:

3.1 mm (0.122 in.)


Maximum length:

3.8 mm (0.150 in.)


If the length is more than the maximum, replace the starter armature assembly.


Hide 28130 4.INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY

a.

Check the brush length.

i.
A296177
2.896,0.792 3.208,0.948 0.313,0.156 10 *1
*1 Length


Using a vernier caliper, measure the brush length.

Standard length:

9.0 mm (0.354 in.)


Minimum length:

4.0 mm (0.157 in.)


If the length is less than the minimum, replace the starter commutator end frame assembly.



b.

Check the resistance.

i.
A296178

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) brush - Negative (-) brush Always 10 kΩ or higher


If the result is not as specified, replace the starter commutator end frame assembly.



Hide 5.INSPECT STARTER CLUTCH

a.

Check the starter clutch.

i.
A296179
1.677,0.24 1.99,0.396 0.313,0.156 10 *a 1.76,1.583 2.073,1.74 0.313,0.156 10 *b
*a Lock
*b Free


Rotate the clutch pinion gear counterclockwise and check that it turns freely. Try to rotate the clutch pinion gear clockwise and check that it locks.

If necessary, replace the repair service starter kit.