Home › Engine / Hybrid System › 2AR-FE STARTING › STARTER(for 1.7 kW Type)
RM3090E _51 Engine / Hybrid System _008402 2AR-FE STARTING _0049375 STARTER(for 1.7 kW Type) A

2AR-FE STARTING  STARTER(for 1.7 kW Type)  REASSEMBLY  


PROCEDURE

Hide 28255 1.INSTALL PLANETARY GEAR

a.
A296180
1.448,0.958 1.406,0.885 false
V100135

High-temperature grease


Apply high-temperature grease to the planetary gears and pin parts of the planetary shaft.


b.

Install the 3 planetary gears to the repair service starter kit.


Hide 28160 2.INSTALL STARTER ARMATURE ASSEMBLY

a.
A224224
2.125,1.323 2.115,1.292 false
V100135

High-temperature grease


Apply high-temperature grease to the washer and starter armature shaft.


b.

Install the starter armature assembly to the starter commutator end frame assembly.


c.

Using snap ring pliers, install the washer and a new snap ring.

NOTICE:
·

Be sure to install the snap ring in the armature shaft groove securely.

·

Be sure to install the snap ring properly because it easily expands.




d.
A295770
1.698,0.417 1.979,0.583 0.281,0.167 10 *1
*1 Length


Using a vernier caliper, measure the snap ring.

Maximum length:

5.0 mm (0.197 in.)


If the length is more than the maximum, replace the snap ring with a new one.


Hide 28132A 3.INSTALL STARTER COMMUTATOR END FRAME COVER

a.
A296181

Install the starter commutator end frame cover to the starter commutator end frame assembly.


Hide 28177 4.INSTALL STARTER ARMATURE PLATE

A295771
1.167,0.406 1.406,0.406 1.406,0.406 1.833,0.823 true 0.365,1.177 0.583,1.604 0.583,1.604 0.76,1.604 true 0.781,1.49 1.094,1.646 0.313,0.156 10 *1 0.938,0.292 1.25,0.448 0.313,0.156 10 *2
*1 Key
*2 Keyway


a.

Align the key of the starter armature plate with the keyway inside the starter yoke assembly, and install the starter armature plate.


Hide 28130 5.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A296182
0.76,0.542 1,0.542 1,0.542 1.552,0.875 true 1.302,0.156 1.521,0.156 1.521,0.156 2,0.521 true 1.115,0.052 1.427,0.208 0.313,0.156 10 *1 0.583,0.427 0.896,0.583 0.313,0.156 10 *2
*1 Rubber Part
*2 Cutout


Align the rubber part on the starter commutator end frame with the cutout of the starter yoke assembly.


b.

Install the starter commutator end frame assembly to the starter yoke assembly.

NOTICE:

The magnet of the starter yoke assembly may attract the starter armature assembly when the starter commutator end frame assembly is installed, causing the magnet to break.



Hide 28120 6.INSTALL STARTER YOKE ASSEMBLY

a.
A296183
1.646,1.24 1.865,1.521 1.865,1.521 2.073,1.521 false 0.646,1.198 1.427,1.198 true 0.479,1.104 0.792,1.26 0.313,0.156 10 *1 2.115,1.448 2.427,1.604 0.313,0.156 10 *2
*1 Cutout
*2 Protrusion


Align the protrusion of the starter yoke assembly with the cutout of the repair service starter kit.


b.

Install the starter yoke assembly with the 2 through bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28226A 7.INSTALL MOTOR TERMINAL STARTER KIT

a.
A296184

Apply high-temperature grease to the plunger, return spring and hook.


b.

Hang the plunger hook of the motor terminal starter kit on the drive lever hook.


c.

Install the plunger and return spring.


d.

Install the motor terminal starter kit with the 2 screws.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


e.

Connect the lead wire to terminal C with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)