Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › BLOCKING SYSTEM › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048167 BLOCKING SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  BLOCKING SYSTEM  TERMINALS OF ECU  


CHECK TELEPHONE TRANSCEIVER ASSEMBLY


a.
F100694
1.552,0.219 1.885,0.438 0.333,0.219 1.583,0.26 1.875,0.469 0.292,0.208 10 G58

Disconnect the G58 telephone transceiver assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

If the result is not as specified, there may be a malfunction on the wire harness side.

G58-6 (IG2) - G58-9 (E) SB - W-B Ignition power supply Ignition switch off Below 1 V
G58-6 (IG2) - G58-9 (E) SB - W-B Ignition power supply Ignition switch ON 9 to 16 V
G58-12 (+B) - G58-9 (E) BR - W-B +B power supply Always 9 to 16 V
G58-9 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the G58 telephone transceiver assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: w/ Entry and Start System

*2: w/o Entry and Start System

G58-1 (BLK1) - G58-9 (E) LG - W-B Certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2 communication input Ignition switch off 11 to 14 V
G58-1 (BLK1) - G58-9 (E) LG - W-B Certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2 communication input Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
G58-2 (BLK4) - G58-9 (E) P - W-B Certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2 communication input Ignition switch off Below 1 V
G58-2 (BLK4) - G58-9 (E) P - W-B Certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2 communication input Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
G58-7 (BLK2) - G58-9 (E) LG - W-B ECM communication output Ignition switch off Below 1 V
G58-7 (BLK2) - G58-9 (E) LG - W-B ECM communication output Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
G58-8 (BLK3) - G58-9 (E) P - W-B ECM communication input Ignition switch off Below 1 V
G58-8 (BLK3) - G58-9 (E) P - W-B ECM communication input Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)


e.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C04
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection
·

G58-1 (BLK1) - G58-9 (E)

·

G58-7 (BLK2) - G58-9 (E)


Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C04
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection
·

G58-2 (BLK4) - G58-9 (E)

·

G58-8 (BLK3) - G58-9 (E)


Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.

B264892
1.958,0.729 2.354,0.969 0.396,0.24 3.344,0.729 3.74,0.969 0.396,0.24 4.917,0.729 5.313,0.969 0.396,0.24 2,0.781 2.344,0.958 0.344,0.177 10 G82 3.385,0.781 3.781,0.969 0.396,0.188 10 G83 4.958,0.781 5.365,0.958 0.406,0.177 10 G84


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

If the result is not as specified, there may be a malfunction on the wire harness side.

G82-11 (E) - Body ground BR - Body ground Ground Always Below 1 Ω
G82-2 (+B) - G82-11 (E) W - BR +B power supply Always 11 to 14 V


c.

Reconnect the G82 certification ECU (smart key ECU assembly) connector.


d.

Measure the waveform and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G82-14 (EFII) - G82-11 (E) LG - BR ECM input signal Engine switch off 11 to 14 V
G82-14 (EFII) - G82-11 (E) LG - BR ECM input signal Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
G82-13 (EFIO) - G82-11 (E) P - BR ECM output signal Engine switch off Below 1 V
G82-13 (EFIO) - G82-11 (E) P - BR ECM output signal Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)


e.

Inspect using an oscilloscope.

i.

Waveform 1 (Reference)

B325134C04
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G82-14 (EFII) - G82-11 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C04
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G82-13 (EFIO) - G82-11 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal




CHECK TRANSPONDER KEY ECU ASSEMBLY (w/o Entry and Start System)


B271269N04
3.24,0.667 3.656,0.938 0.417,0.271 3.302,0.719 3.76,0.917 0.458,0.198 10 G88

a.

Disconnect the G88 transponder key ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G88-1 (+B) - G88-5 (GND) BE - BR +B power supply Always 11 to 14 V
G88-2 (IG) - G88-5 (GND) LG - BR Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
G88-5 (GND) - Body ground BR - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the G88 transponder key ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G88-12 (EFII) - G88-5 (GND) LG - BR ECM input signal Ignition switch off 11 to 14 V
G88-12 (EFII) - G88-5 (GND) LG - BR ECM input signal Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal. Pulse generation
(See waveform 1)
G88-13 (EFIO) - G88-5 (GND) P - BR ECM output signal Ignition switch off Below 1 V
G88-13 (EFIO) - G88-5 (GND) P - BR ECM output signal Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal. Pulse generation
(See waveform 2)


e.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B325134C02
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G88-12 (EFII) - G88-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal.


ii.

Waveform 2 (Reference)

B333259C01
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G88-13 (EFIO) - G88-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal.




CHECK ECM (3ZR-FE)


A247842
5.615,0.448 6,0.688 0.385,0.24 2.313,0.427 2.719,0.646 0.406,0.219 5.677,0.49 6,0.646 0.323,0.156 10 A62 2.385,0.458 2.771,0.656 0.385,0.198 10 B75

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


a.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: w/ Entry and Start System

*2: w/o Entry and Start System

B75-16 (E1) - Body ground BR - Body ground Ground Always Below 1 Ω
B75-51 (E01) - Body ground W-B - Body ground Ground Always Below 1 Ω
B75-21 (E02) - Body ground W-B - Body ground Ground Always Below 1 Ω
B75-52 (E04) - Body ground W-B - Body ground Ground Always Below 1 Ω
A62-50 (EC) - Body ground W-B - Body ground Ground Always Below 1 Ω
B75-59 (ME01) - Body ground W-B - Body ground Ground Always Below 1 Ω
A62-1 (BATT) - B75-16 (E1) W - BR Battery (for measuring battery voltage and for ECM memory) Always 9 to 14 V
A62-2 (+B) - B75-16 (E1) R - BR Power source of ECM Ignition switch off Below 1 V
Ignition switch ON 9 to 14 V
A62-3 (+B2) - B75-16 (E1) P - BR Power source of ECM Ignition switch off Below 1 V
Ignition switch ON 9 to 14 V
A62-28 (IMI) - B75-16 (E1) P - BR Certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2 input signal Ignition switch off Below 1 V
A62-28 (IMI) - B75-16 (E1) P - BR Certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2 input signal Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 1)
A62-29 (IMO) - B75-16 (E1) LG - BR Certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2 output signal Ignition switch off Below 1 V
A62-29 (IMO) - B75-16 (E1) LG - BR Certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2 output signal Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 2)


b.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C04
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A62-29 (IMO) - B75-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C04
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A62-28 (IMI) - B75-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (2AR-FE)


A247842
5.625,0.469 6.01,0.677 0.385,0.208 2.323,0.427 2.698,0.635 0.375,0.208 5.677,0.49 6,0.646 0.323,0.156 10 A62 2.385,0.458 2.771,0.656 0.385,0.198 10 B77

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


a.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: w/ Entry and Start System

*2: w/o Entry and Start System

B77-16 (E1) - Body ground BR - Body ground Ground Always Below 1 Ω
B77-50 (E01) - Body ground W-B - Body ground Ground Always Below 1 Ω
B77-49 (E02) - Body ground W-B - Body ground Ground Always Below 1 Ω
B77-53 (E04) - Body ground W-B - Body ground Ground Always Below 1 Ω
A62-14 (EC) - Body ground W-B - Body ground Ground Always Below 1 Ω
B77-58 (ME01) - Body ground W-B - Body ground Ground Always Below 1 Ω
A62-1 (BATT) - B77-16 (E1) W - BR Battery (for measuring battery voltage and for ECM memory) Always 9 to 14 V
A62-2 (+B) - B77-16 (E1) R - BR Power source of ECM Ignition switch off Below 1 V
Ignition switch ON 9 to 14 V
A62-3 (+B2) - B77-16 (E1) P - BR Power source of ECM Ignition switch off Below 1 V
Ignition switch ON 9 to 14 V
A62-28 (IMI) - B77-16 (E1) P - BR Certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2 input signal Ignition switch off Below 1 V
A62-28 (IMI) - B77-16 (E1) P - BR Certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2 input signal Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 1)
A62-29 (IMO) - B77-16 (E1) LG - BR Certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2 output signal Ignition switch off Below 1 V
A62-29 (IMO) - B77-16 (E1) LG - BR Certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2 output signal Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 2)


b.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C04
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A62-29 (IMO) - B77-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C04
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A62-28 (IMI) - B77-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal