Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › BLOCKING SYSTEM › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048167 BLOCKING SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  BLOCKING SYSTEM  B1586  Open in Immobiliser Communication Circuit  


DESCRIPTION

When the communication line (EFIO - BLK4) between the certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2 and telephone transceiver assembly is open, the telephone transceiver assembly stores DTC B1586.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1586 Open in Immobiliser Communication Circuit The communication line (EFIO - BLK4) between the certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2 and telephone transceiver assembly is open.
·

Telephone transceiver assembly

·

Certification ECU (smart key ECU assembly)*1

·

Transponder key ECU assembly*2

·

Harness or connector



*1: w/ Entry and Start System

*2: w/o Entry and Start System


WIRING DIAGRAM

B341302E01
0.063,3.365 2.208,3.625 2.146,0.26 10 *2: w/o Entry and Start System 4.25,0.635 4.531,0.854 0.281,0.219 10 12 4.281,2.26 4.563,2.479 0.281,0.219 10 9 2.813,0.656 3.094,0.875 0.281,0.219 10 1 2.813,1.104 3.094,1.323 0.281,0.219 10 2 3,0.771 3.667,0.99 0.667,0.219 10 BLK1 2.99,1.219 3.51,1.438 0.521,0.219 10 BLK4 5.927,1.656 6.302,1.875 0.375,0.219 10 IMO 5.948,2.021 6.323,2.24 0.375,0.219 10 IMI 3.813,1.729 4.208,1.958 0.396,0.229 10 BLK2 3.813,2.052 4.188,2.271 0.375,0.219 10 BLK3 2.479,2.958 2.854,3.177 0.375,0.219 10 G58 0.813,1.604 1.323,1.802 0.51,0.198 10 G82*1 0.74,0.802 1.115,1.021 0.375,0.219 10 11*1 0.792,1.073 1.177,1.271 0.385,0.198 10 5*2 2.323,0.438 2.771,0.667 0.448,0.229 10 14*1 1.135,0.802 1.51,1 0.375,0.198 10 E*1 1.104,1.083 1.625,1.281 0.521,0.198 10 GND*2 1.958,0.771 2.333,0.969 0.375,0.198 10 EFII 1.927,1.229 2.302,1.427 0.375,0.198 10 EFIO 5.896,2.427 6.271,2.625 0.375,0.198 10 A62 0.813,1.76 2.604,2.146 1.792,0.385 10 Certification ECU (Smart Key ECU Assembly) 5.667,1.917 5.948,2.135 0.281,0.219 10 28 5.677,1.615 5.958,1.833 0.281,0.219 10 29 4.281,1.917 4.563,2.135 0.281,0.219 10 8 4.281,1.625 4.563,1.844 0.281,0.219 10 7 4.042,2.406 4.323,2.625 0.281,0.219 10 E 0.802,2.323 1.313,2.521 0.51,0.198 10 G88*2 2.344,1.115 2.667,1.302 0.323,0.188 10 13 3.958,0.719 4.333,0.938 0.375,0.219 10 +B 3.917,1.24 4.292,1.458 0.375,0.219 10 IG2 4.281,1.125 4.563,1.344 0.281,0.219 10 6 4.49,0.865 5.438,1.073 0.948,0.208 10 ECU-B NO. 1 4.75,1.375 5.167,1.583 0.417,0.208 10 IGN 5.74,0.698 6.688,0.906 0.948,0.208 10 from Battery 5.74,1.198 6.688,1.406 0.948,0.208 10 from IG2 Relay 2.323,0.635 2.74,0.833 0.417,0.198 10 12*2 2.469,3.125 4.792,3.354 2.323,0.229 10 Telephone Transceiver Assembly 0.052,3.083 2.198,3.344 2.146,0.26 10 *1: w/ Entry and Start System 0.792,2.49 2.896,2.75 2.104,0.26 10 Transponder Key ECU Assembly 5.885,2.604 6.354,2.833 0.469,0.229 10 ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Before troubleshooting for this DTC, make sure no immobiliser system DTCs are output. If output, troubleshoot the immobiliser system DTCs first.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the telephone transceiver assembly, certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2, refer to the Service Bulletin.

·

When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.


*1: w/ Entry and Start System

*2: w/o Entry and Start System



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

After 10 seconds have elapsed, check for DTCs.

Body Electrical > Telematics > Trouble Codes
50001 233

Result:
Proceed to
DTC B1586 is not output
Only DTC B1586 is output (w/ Entry and Start System)
Only DTC B1586 is output (w/o Entry and Start System)
DTC B1586 and other DTCs are output



DTC B1586 is not output

Only DTC B1586 is output (w/ Entry and Start System)

2.CHECK CONNECTION OF CONNECTORS

Only DTC B1586 is output (w/o Entry and Start System)

9.CHECK CONNECTION OF CONNECTORS

DTC B1586 and other DTCs are output

2.CHECK CONNECTION OF CONNECTORS
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the telephone transceiver assembly and certification ECU (smart key ECU assembly).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

NG

CONNECT CONNECTORS CORRECTLY

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
a.

Disconnect the G58 telephone transceiver assembly connector.


b.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-2 (BLK4) - G82-13 (EFIO) Always Below 1 Ω
G58-2 (BLK4) - Body ground Always 10 kΩ or higher
G82-13 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT)
a.

Reconnect the G58 telephone transceiver assembly connector.


b.

Reconnect the G82 certification ECU (smart key ECU assembly) connector.


c.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


B278908C01
2.094,0.188 2.469,0.417 0.375,0.229 2.719,1.042 2.99,1.615 false 2.49,1.042 2.344,1.615 false 0.917,3.115 1.271,3.271 0.354,0.156 10 GND 1.49,0.042 1.656,0.198 0.167,0.156 10 *a 2.146,0.229 2.448,0.385 0.302,0.156 10 G82 2.063,1.625 2.417,1.771 0.354,0.146 10 EFIO 2.958,1.625 3.094,1.771 0.135,0.146 10 E 3.125,3.208 3.302,3.375 0.177,0.167 10 *b 3.313,3.208 3.49,3.375 0.177,0.167 10 *c
*a Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
*b Approximately 160 ms
*c Approximately 270 ms - -


Measurement Condition
Tester Connection Content
Tester Connection G82-13 (EFIO) - G82-11 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal

OK:

The waveform is output normally (refer to illustration).



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - BATTERY AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
B263444N01
1.458,0.104 1.927,0.385 0.469,0.281 1.667,1.271 1.448,1.646 1.448,1.646 1.271,1.646 false 2.146,1.26 2.385,1.646 2.385,1.646 2.563,1.646 false 2.135,0.979 2.365,0.604 2.365,0.604 2.542,0.604 false 1.573,0.146 1.927,0.344 0.354,0.198 10 G58 1.146,1.563 1.26,1.76 0.115,0.198 10 E 2.604,1.563 2.802,1.76 0.198,0.198 10 +B 2.594,0.51 2.896,0.708 0.302,0.198 10 IG2

Disconnect the G58 telephone transceiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-9 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G58-12 (+B) - Body ground Always 11 to 14 V
G58-6 (IG2) - Body ground Engine switch off Below 1 V
G58-6 (IG2) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.PERFORM REGISTRATION
7.PERFORM REGISTRATION
a.

Perform the registration.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

b.

Turn the engine switch on (IG).


c.

After 10 seconds have elapsed, check for DTCs.

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

DTC B1586 is not output.



Result:
Proceed to
DTC B1586 is not output
DTC B1586 is output



DTC B1586 is not output

END (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] WAS DEFECTIVE)

DTC B1586 is output

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

9.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Check that the connectors are properly connected to the telephone transceiver assembly and transponder key ECU assembly.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY)

NG

CONNECT CONNECTORS CORRECTLY

10.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the G58 telephone transceiver assembly connector.


b.

Disconnect the G88 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-2 (BLK4) - G88-13 (EFIO) Always Below 1 Ω
G58-2 (BLK4) - Body ground Always 10 kΩ or higher
G88-13 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK TRANSPONDER KEY ECU ASSEMBLY (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK TRANSPONDER KEY ECU ASSEMBLY (OUTPUT)
a.

Reconnect the G58 telephone transceiver assembly connector.


b.

Reconnect the G88 transponder key ECU assembly connector.


c.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


B341223C02
3.302,0.125 3.708,0.333 0.406,0.208 3.156,0.885 2.875,1.313 2.875,1.313 2.698,1.313 false 3.375,0.969 3.385,1.5 3.385,1.5 3.188,1.5 false 1.75,0.25 2.063,0.406 0.313,0.156 10 *a 3.063,3.177 3.375,3.333 0.313,0.156 10 *b 3.25,3.167 3.563,3.323 0.313,0.156 10 *c 3.354,0.146 3.719,0.333 0.365,0.188 10 G88 2.365,1.219 2.729,1.406 0.365,0.188 10 GND 2.813,1.427 3.313,1.615 0.5,0.188 10 EFIO 0.823,2.99 1.188,3.177 0.365,0.188 10 GND
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Approximately 160 ms
*c Approximately 270 ms - -


Measurement Condition
Tester Connection Content
Tester Connection G88-13 (EFIO) - G88-5 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

OK:

The waveform is output normally (refer to illustration).



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

12.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - BATTERY AND BODY GROUND)
12.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
B263444N01
1.458,0.104 1.927,0.385 0.469,0.281 1.667,1.271 1.448,1.646 1.448,1.646 1.271,1.646 false 2.146,1.26 2.385,1.646 2.385,1.646 2.563,1.646 false 2.135,0.979 2.365,0.604 2.365,0.604 2.542,0.604 false 1.573,0.146 1.927,0.344 0.354,0.198 10 G58 1.146,1.563 1.26,1.76 0.115,0.198 10 E 2.604,1.563 2.802,1.76 0.198,0.198 10 +B 2.594,0.51 2.896,0.708 0.302,0.198 10 IG2

Disconnect the G58 telephone transceiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-9 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G58-12 (+B) - Body ground Always 11 to 14 V
G58-6 (IG2) - Body ground Ignition switch off Below 1 V
G58-6 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

14.PERFORM REGISTRATION
14.PERFORM REGISTRATION
a.

Perform the registration.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

15.CHECK FOR DTC
15.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

b.

Turn the ignition switch to ON.


c.

After 10 seconds have elapsed, check for DTCs.

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

DTC B1586 is not output.



Result:
Proceed to
DTC B1586 is not output
DTC B1586 is output



DTC B1586 is not output

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

DTC B1586 is output

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY