Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › BLOCKING SYSTEM › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048167 BLOCKING SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  BLOCKING SYSTEM  B1587  Lost Communication for Immobiliser Communication Circuit  


DESCRIPTION

When one of the following occurs: 1) the telephone transceiver assembly detects errors in its own communications with the certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2, 2) the telephone transceiver assembly detects errors in the communication lines, or 3) the ECU communication ID between the certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2 and telephone transceiver assembly is different and an engine start is attempted, the telephone transceiver assembly stores DTC B1587.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1587 Lost Communication for Immobiliser Communication Circuit
Either condition is met:
·

An error in communication between the telephone transceiver assembly and certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2

·

An error in communication lines

·

The communication ID is different during communication with the certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2


·

Telephone transceiver assembly

·

Certification ECU (smart key ECU assembly)*1

·

Transponder key ECU assembly*2

·

Harness or connector



*1: w/ Entry and Start System

*2: w/o Entry and Start System


WIRING DIAGRAM

B341302E01
0.063,3.365 2.208,3.625 2.146,0.26 10 *2: w/o Entry and Start System 4.25,0.635 4.531,0.854 0.281,0.219 10 12 4.281,2.26 4.563,2.479 0.281,0.219 10 9 2.813,0.656 3.094,0.875 0.281,0.219 10 1 2.813,1.104 3.094,1.323 0.281,0.219 10 2 3,0.771 3.667,0.99 0.667,0.219 10 BLK1 2.99,1.219 3.51,1.438 0.521,0.219 10 BLK4 5.927,1.656 6.302,1.875 0.375,0.219 10 IMO 5.948,2.021 6.323,2.24 0.375,0.219 10 IMI 3.813,1.729 4.208,1.958 0.396,0.229 10 BLK2 3.813,2.052 4.188,2.271 0.375,0.219 10 BLK3 2.479,2.958 2.854,3.177 0.375,0.219 10 G58 0.813,1.604 1.323,1.802 0.51,0.198 10 G82*1 0.74,0.802 1.115,1.021 0.375,0.219 10 11*1 0.792,1.073 1.177,1.271 0.385,0.198 10 5*2 2.323,0.438 2.771,0.667 0.448,0.229 10 14*1 1.135,0.802 1.51,1 0.375,0.198 10 E*1 1.104,1.083 1.625,1.281 0.521,0.198 10 GND*2 1.958,0.771 2.333,0.969 0.375,0.198 10 EFII 1.927,1.229 2.302,1.427 0.375,0.198 10 EFIO 5.896,2.427 6.271,2.625 0.375,0.198 10 A62 0.813,1.76 2.604,2.146 1.792,0.385 10 Certification ECU (Smart Key ECU Assembly) 5.667,1.917 5.948,2.135 0.281,0.219 10 28 5.677,1.615 5.958,1.833 0.281,0.219 10 29 4.281,1.917 4.563,2.135 0.281,0.219 10 8 4.281,1.625 4.563,1.844 0.281,0.219 10 7 4.042,2.406 4.323,2.625 0.281,0.219 10 E 0.802,2.323 1.313,2.521 0.51,0.198 10 G88*2 2.344,1.115 2.667,1.302 0.323,0.188 10 13 3.958,0.719 4.333,0.938 0.375,0.219 10 +B 3.917,1.24 4.292,1.458 0.375,0.219 10 IG2 4.281,1.125 4.563,1.344 0.281,0.219 10 6 4.49,0.865 5.438,1.073 0.948,0.208 10 ECU-B NO. 1 4.75,1.375 5.167,1.583 0.417,0.208 10 IGN 5.74,0.698 6.688,0.906 0.948,0.208 10 from Battery 5.74,1.198 6.688,1.406 0.948,0.208 10 from IG2 Relay 2.323,0.635 2.74,0.833 0.417,0.198 10 12*2 2.469,3.125 4.792,3.354 2.323,0.229 10 Telephone Transceiver Assembly 0.052,3.083 2.198,3.344 2.146,0.26 10 *1: w/ Entry and Start System 0.792,2.49 2.896,2.75 2.104,0.26 10 Transponder Key ECU Assembly 5.885,2.604 6.354,2.833 0.469,0.229 10 ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Before troubleshooting for these DTCs, make sure no immobiliser system DTCs are output. If output, troubleshoot the immobiliser system DTCs first.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the telephone transceiver assembly, certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2, refer to the Service Bulletin.

·

When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.


*1: w/ Entry and Start System

*2: w/o Entry and Start System



HINT:
·

When DTC B1587 and B2799 are output simultaneously, perform troubleshooting for DTC B2799 first.

·

After troubleshooting for this DTC, make sure B2799 is not output. If output, troubleshoot the blocking system DTCs next.



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

Result:
Proceed to
DTC B1587 is not output
DTC B1587 is output



DTC B1587 is not output

DTC B1587 is output

2.PERFORM ECU COMMUNICATION ID
2.PERFORM ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233

Result:
Proceed to
DTC B1587 is not output
DTC B1587 is output



DTC B1587 is not output

END

DTC B1587 is output

4.CHECK CONNECTION OF CONNECTORS
4.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Check that the connectors are properly connected to the telephone transceiver assembly and certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2.

*1: w/ Entry and Start System

*2: w/o Entry and Start System


OK:

Connectors are properly connected.



Result:
Proceed to
OK (w/ Entry and Start System)
OK (w/o Entry and Start System)
NG



OK (w/ Entry and Start System)

5.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

OK (w/o Entry and Start System)

9.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY)

NG

CONNECT CONNECTORS CORRECTLY

5.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G58 telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-1 (BLK1) - G82-14 (EFII) Always Below 1 Ω
G58-1 (BLK1) or G82-14 (EFII) - Body ground Always 10 kΩ or higher
G58-2 (BLK4) - G82-13 (EFIO) Always Below 1 Ω
G58-2 (BLK4) or G82-13 (EFIO) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G58-1 (BLK1) - Body ground Always Below 1 V
G58-2 (BLK4) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

6.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

b.

Turn the engine switch off.


c.

Start the engine.


d.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233

Result:
Proceed to
DTC B1587 is not output
DTC B1587 is output



DTC B1587 is not output

END (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] WAS DEFECTIVE)

DTC B1587 is output

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the G88 transponder key ECU assembly connector.


b.

Disconnect the G58 telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-1 (BLK1) - G88-12 (EFII) Always Below 1 Ω
G58-1 (BLK1) or G88-12 (EFII) - Body ground Always 10 kΩ or higher
G58-2 (BLK4) - G88-13 (EFIO) Always Below 1 Ω
G58-2 (BLK4) or G88-13 (EFIO) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G58-1 (BLK1) - Body ground Always Below 1 V
G58-2 (BLK4) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.REGISTER ECU COMMUNICATION ID
11.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTC
12.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233

Result:
Proceed to
DTC B1587 is not output
DTC B1587 is output



DTC B1587 is not output

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

DTC B1587 is output

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY