Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048165 THEFT DETERRENT SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  B2764  Short to GND in Intrusion Sensor Signal Circuit  


DESCRIPTION

The intrusion sensor (theft warning ultrasonic sensor) conducts self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).

If a malfunction is detected in the ISIF line, the main body ECU (multiplex network body ECU) stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2764 Short to GND in Intrusion Sensor Signal Circuit
After normal/trouble signal is output from intrusion sensor (theft warning ultrasonic sensor) as result of self-diagnosis, following malfunctions are detected:
1.

ISIF line circuit is shorted to ground

2.

Reception of signals other than normal/trouble signal


·

Map light assembly

·

Intrusion sensor (theft warning ultrasonic sensor)

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

B300521E10
5.646,2.135 6.229,2.354 0.583,0.219 10 SSW1 5.646,1.698 5.958,1.927 0.313,0.229 10 ISIF 5.365,3.052 7.063,3.448 1.698,0.396 10 Main Body ECU (Multiplex Network Body ECU) 5.365,2.875 6.063,3.229 0.698,0.354 10 G79 3.479,1.698 3.833,1.865 0.354,0.167 10 IOUT 2.063,2.719 2.99,3.042 0.927,0.323 10 Q7 3.427,2.125 3.906,2.333 0.479,0.208 10 SOFF 2.063,2.875 3.688,3.083 1.625,0.208 10 Map Light Assembly 1.375,1.771 1.844,2 0.469,0.229 10 GND3 1.177,1.635 1.365,1.865 0.188,0.229 10 1 1.74,0.281 2.948,0.542 1.208,0.26 10 from Battery 2.01,1.354 3.167,1.875 1.156,0.521 10 Intrusion Sensor (Theft Warning Ultrasonic Sensor) 5.396,2.01 5.802,2.354 0.406,0.344 10 8 5.385,1.563 5.927,1.896 0.542,0.333 10 12 3.906,1.573 4.219,1.802 0.313,0.229 10 8 3.552,1.25 3.865,1.438 0.313,0.188 10 +B2 3.896,1.146 4.156,1.354 0.26,0.208 10 6 3.906,1.99 4.24,2.188 0.333,0.198 10 7 3.49,0.438 4.469,0.646 0.979,0.208 10 ECU-B NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.CHECK WAVEFORM (INTRUSION SENSOR [THEFT WARNING ULTRASONIC SENSOR]) (IOUT)
a.

Using an oscilloscope, check the waveform.

B341515C02
3.313,0.083 3.729,0.323 0.417,0.24 3.729,1.271 4.313,1.854 false 1.76,2.76 1.917,2.906 false 2.271,2.76 2.427,2.906 false 3.448,0.125 3.698,0.302 0.25,0.177 10 false Q7 4.177,1.885 4.688,2.063 0.51,0.177 10 false IOUT 1.26,2.49 1.51,2.667 0.25,0.177 10 false *k 1.25,2.948 1.5,3.125 0.25,0.177 10 false *l 1.698,0.177 2.01,0.333 0.313,0.156 10 false *a 1.583,2.646 1.896,2.802 0.313,0.156 10 false *b 2.094,2.646 2.406,2.802 0.313,0.156 10 false *c 3.979,2.646 4.292,2.802 0.313,0.156 10 false *d 4,3.177 4.313,3.333 0.313,0.156 10 false *e 2.146,3.229 2.458,3.385 0.313,0.156 10 false *f 2.5,3.219 3.063,3.51 0.563,0.292 10 false *g 2.667,3.583 3.094,3.792 0.427,0.208 10 false *h 1.542,4.115 1.875,4.354 0.333,0.24 10 false *i 3.771,4.125 4.031,4.396 0.26,0.271 10 false *j
*a Component with harness connected
(Map Light Assembly)
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 seconds
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State
*k HI *l LO


Measurement Condition
Tester Connection Content
Tester Connection Q7-8 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the intrusion sensor (theft warning ultrasonic sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).



Result:
Proceed to
OK
NG



OK

NG

2.CHECK VOLTAGE (INTRUSION SENSOR [THEFT WARNING ULTRASONIC SENSOR]) (IOUT)
2.CHECK VOLTAGE (INTRUSION SENSOR [THEFT WARNING ULTRASONIC SENSOR]) (IOUT)
a.
E255911C02
1.646,0.146 2.063,0.406 0.417,0.26 1.875,1.531 1.635,1.208 false 1.24,1.563 1.479,1.063 false 1.76,0.198 2.073,0.396 0.313,0.198 10 Q7 1.052,1.604 1.51,1.844 0.458,0.24 10 GND3 1.76,1.583 2.104,1.802 0.344,0.219 10 IOUT 0.167,0.135 0.625,0.375 0.458,0.24 10 *a
*a Front view of wire harness connector
(to Map Light Assembly)


Disconnect the map light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition
Q7-8 (IOUT) - Q7-1 (GND3) Immediately after theft deterrent system set


Result:
Result Proceed to
IOUT voltage is below 1 V when theft deterrent system is set A
IOUT voltage is 6.5 V or higher when theft deterrent system is set B


HINT:

With connector Q7 of the map light assembly disconnected, measure the voltage at IOUT when the theft deterrent system is set.




A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY)

B

4.REPLACE MAP LIGHT ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY)
a.

Disconnect the G79 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the Q7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-12 (ISIF) - Q7-8 (IOUT) Always Below 1 Ω
G79-12 (ISIF) - Body ground Always 10 kΩ or higher
Q7-8 (IOUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE MAP LIGHT ASSEMBLY
a.

Temporarily replace the map light assembly with a new or normally functioning one.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Turn the ignition switch to ON, then off.


c.

Set the theft deterrent system to "ARMED STATE".


d.

Check that the security indicator changes from illuminated to blinking.


e.

Set the theft deterrent system to "DISARMED STATE".


f.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Proceed to
DTC B2764 is not output
DTC B2764 is output



DTC B2764 is not output

END (MAP LIGHT ASSEMBLY WAS DEFECTIVE)

DTC B2764 is output

REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)