Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048165 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the security horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B341517E01
0.26,0.958 1.125,1.177 0.865,0.219 10 from Battery 1.427,1.115 2.104,1.313 0.677,0.198 10 S-HORN 2.031,0.802 2.167,0.99 0.135,0.188 10 1 2.052,1.479 2.188,1.667 0.135,0.188 10 5 2.115,1.885 3.156,2.094 1.042,0.208 10 S-HORN Relay 3.021,0.823 3.156,1.01 0.135,0.188 10 2 3.021,1.49 3.156,1.677 0.135,0.188 10 3 3.875,0.74 4.177,0.948 0.302,0.208 10 53 3.875,0.958 4.177,1.167 0.302,0.208 10 3D 5.531,0.969 5.708,1.177 0.177,0.208 10 A 5.5,0.771 5.719,0.99 0.219,0.219 10 17 5.844,0.979 6.156,1.177 0.313,0.198 10 SH 4.146,1.531 5.802,1.875 1.656,0.344 10 Instrument Panel Junction Block Assembly 5.448,3.125 7.094,3.479 1.646,0.354 10 Main Body ECU (Multiplex Network Body ECU) 2.271,2.76 2.635,2.969 0.365,0.208 10 A13 2.271,2.948 3.865,3.167 1.594,0.219 10 Security Horn Assembly 1.917,2.458 2.052,2.646 0.135,0.188 10 1 1.667,2.646 1.823,2.844 0.156,0.198 10 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY HORN)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Horn Security indicator ON or OFF -
Body Electrical > Main Body > Active Test
Tester Display
Security Horn
50004 123 20
OK:

The security horn assembly sounds and stops correctly when operated through the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT SECURITY HORN ASSEMBLY
2.INSPECT SECURITY HORN ASSEMBLY


Result:
Proceed to
OK
NG



OK

3.INSPECT SECURITY HORN RELAY

NG

3.INSPECT SECURITY HORN RELAY
a.
E270109E01
1.948,1.302 2.135,1.302 false 2.698,1.302 2.885,1.302 false 2.542,1.021 2.865,1.021 false 2.552,0.76 2.875,0.76 false 0.458,0.719 0.615,0.917 0.156,0.198 10 false 5 1.271,0.719 1.427,0.917 0.156,0.198 10 false 3 1.271,1.281 1.427,1.479 0.156,0.198 10 false 2 0.458,1.281 0.615,1.479 0.156,0.198 10 false 1 2.927,0.677 3.083,0.875 0.156,0.198 10 false 3 2.917,0.938 3.073,1.135 0.156,0.198 10 false 5 2.948,1.229 3.104,1.427 0.156,0.198 10 false 1 1.813,1.24 1.969,1.438 0.156,0.198 10 false 2

Remove the security horn relay.


b.

Measure the resistance according to the value(s) in the table below

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is applied between terminals 2 - 1 Below 1 Ω
3 - 5 Battery voltage is not applied between terminals 2 - 1 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPLACE SECURITY HORN RELAY

4.CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL


b.

Connect the instrument panel junction block assembly connectors.


c.

Remove the security horn relay.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - A-17 (SH) Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
A-17 (SH) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BATTERY - SECURITY HORN RELAY)

NG

7.CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (BATTERY - SECURITY HORN RELAY)
a.
B341518

Remove the security horn relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 - Body ground Always 11 to 14 V
5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - SECURITY HORN ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - SECURITY HORN ASSEMBLY AND BODY GROUND)
a.

Remove the security horn relay.


b.

Disconnect the A13 security horn assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - A13-1 Always Below 1 Ω
A13-2 - Body ground Always Below 1 Ω
3 - Body ground Always 10 kΩ or higher
A13-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Remove the security horn relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 3D-53 Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
3D-53 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR