Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048165 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Intrusion Sensor Cancel Switch Circuit  


DESCRIPTION

When the intrusion sensor cancel switch on the map light assembly is pressed, the sensor off signal is sent to the main body ECU (multiplex network body ECU) which causes the intrusion sensor to stop operating.

WIRING DIAGRAM

B300521E10
5.646,2.135 6.229,2.354 0.583,0.219 10 SSW1 5.646,1.698 5.958,1.927 0.313,0.229 10 ISIF 5.365,3.052 7.063,3.448 1.698,0.396 10 Main Body ECU (Multiplex Network Body ECU) 5.365,2.875 6.063,3.229 0.698,0.354 10 G79 3.479,1.698 3.833,1.865 0.354,0.167 10 IOUT 2.063,2.719 2.99,3.042 0.927,0.323 10 Q7 3.427,2.125 3.906,2.333 0.479,0.208 10 SOFF 2.063,2.875 3.688,3.083 1.625,0.208 10 Map Light Assembly 1.375,1.771 1.844,2 0.469,0.229 10 GND3 1.177,1.635 1.365,1.865 0.188,0.229 10 1 1.74,0.281 2.948,0.542 1.208,0.26 10 from Battery 2.01,1.354 3.167,1.875 1.156,0.521 10 Intrusion Sensor (Theft Warning Ultrasonic Sensor) 5.396,2.01 5.802,2.354 0.406,0.344 10 8 5.385,1.563 5.927,1.896 0.542,0.333 10 12 3.906,1.573 4.219,1.802 0.313,0.229 10 8 3.552,1.25 3.865,1.438 0.313,0.188 10 +B2 3.896,1.146 4.156,1.354 0.26,0.208 10 6 3.906,1.99 4.24,2.188 0.333,0.198 10 7 3.49,0.438 4.469,0.646 0.979,0.208 10 ECU-B NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.

·

for Australia, New Zealand:

Check that the theft deterrent system customization is set to its initial setting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>CUSTOMIZE PARAMETERS



PROCEDURE

1.READ VALUE USING GTS (INTRUSION SENS OFF SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sens OFF SW Intrusion sensor cancel switch ON or OFF ON: Intrusion sensor cancel switch on
OFF: Intrusion sensor cancel switch off
-
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sens OFF SW
50003 123 203
OK:

The indicator on the GTS switches between ON and OFF in accordance with the intrusion sensor cancel switch status.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY AND BODY GROUND)
a.

Disconnect the G79 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the Q7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-8 (SSW1) - Q7-7 (SOFF) Always Below 1 Ω
Q7-1 (GND3) - Body ground Always Below 1 Ω
G79-8 (SSW1) - Body ground Always 10 kΩ or higher
Q7-7 (SOFF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)
a.
E244514N03
2.49,1.771 2.094,1.552 true 2.094,1.271 2.458,1.104 true 2.51,1.031 3.125,1.229 0.615,0.198 10 GND3 2.583,1.708 3.198,1.906 0.615,0.198 10 SOFF

Remove the map light assembly (intrusion sensor cancel switch).

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (SOFF) - 1 (GND3) Intrusion sensor cancel switch not pressed 10 kΩ or higher
7 (SOFF) - 1 (GND3) Intrusion sensor cancel switch pressed Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)