Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048165 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Intrusion Sensor Circuit  


DESCRIPTION

If no warnings operate or the system can be set even though the conditions to set the system are not met, the main body ECU (multiplex network body ECU) cannot perform recognition due to a cutoff of the ON signal from the courtesy light switch from the doors, engine hood or back door, or some other problem.

If the automatic alarm operates when it should not operate, it may be due to a false detection by the intrusion sensor (theft warning ultrasonic sensor) or due to the ON signal being input when there is a short circuit in the courtesy light switch of the doors, engine hood or back door, or some other problem which would cause this to happen.

HINT:

In the following situations, the intrusion sensor (theft warning ultrasonic sensor) may operate and cause the automatic alarm system to operate even when the sensor is normal.

·

The driver steps away from the vehicle while other people, pets, etc. are in the vehicle.

·

There are things which move easily inside the vehicle, such as things hanging inside the vehicle or clothing hanging from the coat hooks.

·

A window or the sliding roof is open.

·

The vehicle is parked in a place with a lot of vibration or noise such as a parking garage.

·

The vehicle is being washed using a high-pressure spray gun or an automatic car washing machine.

·

The vehicle is continuously being struck or is vibrating due to hail or lightning.

·

The vehicle is continuously being subjected to impacts or is vibrating when snow or ice is being removed from the vehicle.

·

A frost prevention sheet which has an aluminum film is moved by wind, etc.



WIRING DIAGRAM

B300521E10
5.646,2.135 6.229,2.354 0.583,0.219 10 SSW1 5.646,1.698 5.958,1.927 0.313,0.229 10 ISIF 5.365,3.052 7.063,3.448 1.698,0.396 10 Main Body ECU (Multiplex Network Body ECU) 5.365,2.875 6.063,3.229 0.698,0.354 10 G79 3.479,1.698 3.833,1.865 0.354,0.167 10 IOUT 2.063,2.719 2.99,3.042 0.927,0.323 10 Q7 3.427,2.125 3.906,2.333 0.479,0.208 10 SOFF 2.063,2.875 3.688,3.083 1.625,0.208 10 Map Light Assembly 1.375,1.771 1.844,2 0.469,0.229 10 GND3 1.177,1.635 1.365,1.865 0.188,0.229 10 1 1.74,0.281 2.948,0.542 1.208,0.26 10 from Battery 2.01,1.354 3.167,1.875 1.156,0.521 10 Intrusion Sensor (Theft Warning Ultrasonic Sensor) 5.396,2.01 5.802,2.354 0.406,0.344 10 8 5.385,1.563 5.927,1.896 0.542,0.333 10 12 3.906,1.573 4.219,1.802 0.313,0.229 10 8 3.552,1.25 3.865,1.438 0.313,0.188 10 +B2 3.896,1.146 4.156,1.354 0.26,0.208 10 6 3.906,1.99 4.24,2.188 0.333,0.198 10 7 3.49,0.438 4.469,0.646 0.979,0.208 10 ECU-B NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.

·

for Australia, New Zealand:

Check that the theft deterrent system customization is set to its initial setting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>CUSTOMIZE PARAMETERS



PROCEDURE

1.READ VALUE USING GTS (INTRUSION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sensor Status of the intrusion sensor detection ON or OFF ON: Intrusion sensor detected
OFF: Intrusion sensor not detected
-
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sensor
50003 123 204
NOTICE:

After setting the theft deterrent system, wait 30 seconds or more (until the vehicle is in the armed state), and place your hand in the direction of the intrusion sensor (theft warning ultrasonic sensor) and move it back and forth approximately 30 cm (11.8 in.) inside the vehicle.


HINT:

When performing the above inspection, have the electrical key transmitter in the vehicle exterior detection area to perform certification (this prevents the alarm from sounding) (w/ Entry and Start System).


OK:

The display on the GTS changes according to the detection condition of the intrusion sensor (theft warning ultrasonic sensor).



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK WAVEFORM (INTRUSION SENSOR [THEFT WARNING ULTRASONIC SENSOR]) (IOUT)
2.CHECK WAVEFORM (INTRUSION SENSOR [THEFT WARNING ULTRASONIC SENSOR]) (IOUT)
a.

Using an oscilloscope, check the waveform.

B341515C02
3.313,0.083 3.729,0.323 0.417,0.24 3.729,1.271 4.313,1.854 false 1.76,2.76 1.917,2.906 false 2.271,2.76 2.427,2.906 false 3.448,0.125 3.698,0.302 0.25,0.177 10 false Q7 4.177,1.885 4.688,2.063 0.51,0.177 10 false IOUT 1.26,2.49 1.51,2.667 0.25,0.177 10 false *k 1.25,2.948 1.5,3.125 0.25,0.177 10 false *l 1.698,0.177 2.01,0.333 0.313,0.156 10 false *a 1.583,2.646 1.896,2.802 0.313,0.156 10 false *b 2.094,2.646 2.406,2.802 0.313,0.156 10 false *c 3.979,2.646 4.292,2.802 0.313,0.156 10 false *d 4,3.177 4.313,3.333 0.313,0.156 10 false *e 2.146,3.229 2.458,3.385 0.313,0.156 10 false *f 2.5,3.219 3.063,3.51 0.563,0.292 10 false *g 2.667,3.583 3.094,3.792 0.427,0.208 10 false *h 1.542,4.115 1.875,4.354 0.333,0.24 10 false *i 3.771,4.125 4.031,4.396 0.26,0.271 10 false *j
*a Component with harness connected
(Map Light Assembly)
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 seconds
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State
*k HI *l LO


Measurement Condition
Tester Connection Content
Tester Connection Q7-8 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the intrusion sensor (theft warning ultrasonic sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY)
a.

Disconnect the G79 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the Q7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-12 (ISIF) - Q7- 8 (IOUT) Always Below 1 Ω
G79-12 (ISIF) - Body ground Always 10 kΩ or higher
Q7- 8 (IOUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE MAP LIGHT ASSEMBLY
a.

Temporarily replace the map light with a new or normally functioning one.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.READ VALUE USING GTS (INTRUSION SENSOR)
5.READ VALUE USING GTS (INTRUSION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sensor Status of the intrusion sensor detection ON or OFF ON: Intrusion sensor detected
OFF: Intrusion sensor not detected
-
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sensor
50003 123 204
NOTICE:

After setting the theft deterrent system, wait 30 seconds or more (until the vehicle is in the armed state), and place your hand in the direction of the intrusion sensor (theft warning ultrasonic sensor) and move it back and forth approximately 30 cm (11.8 in.) inside the vehicle.


HINT:

When performing the above inspection, have the electrical key transmitter in the vehicle exterior detection area to perform certification (this prevents the alarm from sounding) (w/ Entry and Start System).


OK:

The display on the GTS changes according to the detection condition of the intrusion sensor (theft warning ultrasonic sensor).



Result:
Proceed to
OK
NG



OK

END (MAP LIGHT ASSEMBLY WAS DEFECTIVE)

NG

REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)